Simpact Freeway 2000 Hardware Installation Manual Download

Page: 29 / 86

DC 900-1331F

Chapter

Getting Started

This manual describes how to install the Freeway 2000/4000 hardware and configure

the boot parameters. The following is a summary of the complete installation proce-

dure:

1. Install the hardware as described in

Chapter 2

of this manual.

2. Install the software onto the boot server as described in the

Freeway User’s Guide

3. Configure the Freeway system boot parameters as described in

Chapter 3

of this

manual.

4. Boot the Freeway server.

5. Run the loopback test as described in the

Loopback Test Procedures

6. Customize your installation, if necessary, as described in the

Freeway User’s Guide

7. Familiarize yourself with Freeway operations as described in the

Freeway User’s

Guide

Summary of Contents for Freeway 2000























































































Search results

Summary of Contents for Freeway 2000

Reviews:

Related manuals for Freeway 2000

Brands by name

Popular brands

Simpact Freeway 2000, Hardware Installation Manual

Search results

Summary of Contents for Freeway 2000

Reviews:

Related manuals for Freeway 2000

Brands by name

Popular brands