Simex SWE-94-U, User Manual

Page: 33 / 40

User manual - METER SWE-94-U
Register Write Range Register description
16h Yes 0 ÷ 999 “ Lo r ” parameter in “ InPt ” menu, in 0.1%
17h Yes 0 ÷ 199
“
Hi r
” parameter in “
InPt
” menu, in 0.1%
18h Yes -99 ÷ 99
“ toFS ” parameter in “ InPt ” menu (shift of measurement scale),
expressed by 0.1°C (for RTD input) or by 1.0°C (for TC input)
19h Yes 1 ÷ 2
“ Conn ” parameter in “ InPt ” menu (RTD input connection method):
1 - “ 3 in ”; 2 - “ 2 in ”
20h 1 Yes 0 ÷ 199 Device address
21h No 22DBh Device identification code (ID)
22h 2 Yes 0 ÷ 7
“bAud” parameter in “rS” menu (baud rate);
0 - 1200 baud; 1 - 2400 baud; 2 - 4800 baud; 3 - 9600 baud;
4 - 19200 baud; 5 - 38400 baud; 6 - 57600 baud; 7 - 115200 baud
23h
3
Yes 0 ÷ 1
“mbAc”
parameter in
“rS”
menu (permission to write registers via
RS-485 interface);
0
- write denied ;
1
- write allowed
25h Yes 0 ÷ 5
“rESP” parameter in “rS” menu (additional response delay);
0 - no additional delay; 1 - ” 10c ” option; 2 - ” 20c ” option;
3 - ” 50c ” option; 4 - ” 100c ” option; 5 - ” 200c ” option;
27h Yes 0 ÷ 99
“mbtO”
parameter in
“rS”
menu (maximum delay between
received frames); 0 - no delay checking;
1 ÷ 99 - maximum delay expressed in seconds
2Dh Yes 1 ÷ 8
“ bri ” parameter (display brightness);
1
- the lowest brightness;
8
- the highest brightness
2Fh Yes 0 ÷ 1
“ Edit ” parameter (numerical parameters edit mode);
0 - „ dig ” mode; 1 - „ SLid ” mode
50h Yes 0 ÷ 1
“
modE
” parameter in “
HOLd
” menu (type of detected changes):
0
- peaks;
1
- drops
51h Yes 0 ÷ 9999
“ PEA ” parameter in “ HOLd ” menu (minimum detectable change, no
decimal point included)
52h Yes 0 ÷ 199
“ timE ” parameter in “ HOLd ” menu, maximum peaks' (or drops')
display time expressed in seconds
53h Yes 0 ÷ 1
“
HdiS
” parameter in “
HOLd
” menu:
0
- “
rEAL
” mode ;
1
- “
HOLd
” mode
70h 4 Yes -999 ÷ 1999
The value of „ X ” coordinate of point no. 1 of the user defined
characteristic, expressed in 0.1%
71h 4 Yes -999 ÷ 9999
The value of „ Y ” coordinate of point no. 1 of the user defined
characteristic, no decimal point included
72h
5
÷ 95h
5
Further pairs of „ X ” - „ Y ” coordinates of points no. 2 ÷ 19 of the user
defined characteristic
96h 4 Yes -999 ÷ 1999
The value of „ X ” coordinate of point no. 20 of the user defined
characteristic, expressed in 0.1%
97h 4 Yes -999 ÷ 9999
The value of „
Y
” coordinate of point
no. 20
of the user defined
characteristic, no decimal point included
33