Sime 8115020, User, Installation And Servicing Instructions

Page: 72 / 84

72
EN
7.5 Display of operating data and counters
Once the boiler is operating a qualified technician can view the
operating data
"In"
and the counters
"CO"
as follows:
– from the operating screen in the mode enabled at that mo-
ment (WINTER n or SUMMER l )
– go into "INFO" by pressing the buttons > and < at the same
time
for more than 3 seconds until
"In"
appears alternating
with
"0.0"
(information number) and
"25"
(eg. value)
From this point, the technician has 2 options:
– scroll through the list of
"info"
and
"counters"
by pressing the
button > . This way, scrolling will be in sequence
– display the “activated alarms” (no more than 10) by pressing
the button < . Once in this section, proceed with button > or < .
When all the values have been displayed, exit the menu by
pressing and holding down the button o for approximately 5
seconds until the initial screen is displayed.
TABLE OF INFORMATION DISPLAYED
Type No. Description Range U/M Step
In 0.0 SW version
In 0.1 External sensor
- 9 ..
99
°C 1
In 0.2 Delivery sensor temper-
ature
- 9 ..
99
°C 1
In 0.3 Smoke probe
- 9 ..
99
°C 1
In 0.4 Domestic hot water
sensor temperature
- 9 ..
99
°C 1
In 0.5 AUX auxiliary sensor
- 9 ..
99
°C 1
In 0.6 Actual heating SET
temperature
Par. 13
… Par.
14
°C 1
In 0.7 Power level 0 .. 99 % 1
In 0.8 Flow meter rate 0 .. 99 l/min 0.1
In 0.9 Water pressure trans-
ducer reading (if resent)
0 .. 99 bar 0.1
In 1.0 Display of current fan
revolutions
0 .. 99 RPM x 100 1
TABLE OF COUNTER DISPLAYED
Type No. Description Range U/M Step
CO 0.0 total no. of boiler
operating hours
0 .. 99 h x 1000
0.1; from 0.0
to 9.9; 1; from
10 to 99
CO 0.1 total no. of burner
operating hours
0 .. 99 h x 1000
0.1; from 0.0
to 9.9; 1; from
10 to 99
CO 0.2 total no. of burner
ignitions
0 .. 99 h x 1000
0.1; from 0.0
to 9.9; 1; from
10 to 99
CO 0.3 total no. faults 0 .. 99 x 1 1
CO 0.4
total no. of times
installer parame-
ters "tS"accessed
0 .. 99 x 1 1
CO 0.5
total no. of times
OEM parameters
accessed
0 .. 99 x 1 1
CO 0.6
time unitl next
maintenance inter-
vention
1 .. 199 months 1
TABLE OF ACTIVATED ALARMS/FAULTS
Type No. Description
AL 00 Last activated alarm/fault
AL 01 Last but one activated alarm/fault
AL 02 Third from last activated alarm/fault
AL 03 Previous activated alarm/fault
AL 04 Previous activated alarm/fault
AL 05 Previous activated alarm/fault
AL 06 Previous activated alarm/fault
AL 07 Previous activated alarm/fault
AL 08 Previous activated alarm/fault
AL 09 Previous activated alarm/fault
7.6 Checks
7.6.1 Chimney sweeper function
The chimney sweeper function is used by the qualified mainte-
nance technician to check the mains gas pressure, detect the
combustion parameters and to measure the combustion effi-
ciency required by legislation in force.
This function lasts 15 minutes and is activated by proceeding
as follows:
– if the panel (2) has not already been removed, remove the
two screws (1), pull the front panel (2) forwards and release it
from the top by lifting it
1
2
Fig. 42