GB
6
Before Use
WARNING: Ensure the tool is disconnected from the power supply before attaching or
changing any accessories, or making any adjustments.
Bench mounting
• For added safety the multipurpose sharpener can be secured to a rigid work surface such as a
work bench. This is recommended if the sharpener is to be used in a permanent position
• Use the four Bench Mounting Holes (3) in the base of the Motor Unit as a template to mark and
drill four holes in the intended mounting surface. Secure the Motor Unit in position using bolts,
washers and nuts (not supplied)
• For a portable arrangement, fix a board to the base of the Motor Unit which can be easily
clamped and removed from various mounting surfaces
On-board storage of sharpening modules
• The Module Fixing Slots (6) located on the side faces of the Motor Unit provide on-board storage
for sharpening modules when not in use
• Simply slide the modules into the Module Fixing Slots on the sides of the Motor Unit
Sharpening module
• The sharpening modules provide a guide for safe, precision sharpening of cutting tools
• Do not use the multipurpose sharpener without a sharpening module in place
• There are three sharpening modules:
- Drill Bit Sharpening Module
- Chisel & Plane Sharpening Module
- Knife & Scissor Sharpening Module
Fitting a sharpening module:
1. Slide the appropriate sharpening module into the Module Fixing Slot (6) on the Grinding Wheel
(5) face of the Motor Unit
2. Push the module down until it is fully engaged in the Module Release Lever (7) in the base of the
Motor Unit. You will hear a ‘click’ as it locks into place
Removing a sharpening module:
• Depress the Module Release Lever and pull the module up and out of the Module Fixing
Slot
Operation
WARNING
: ALWAYS wear eye protection, adequate respiratory and hearing protection, as well as
suitable gloves, when working with this tool.
Switching ON and OFF
• Switch the sharpener on by depressing the side of the ON/OFF Switch (4) marked ‘I’
• Switch the sharpener off by depressing the side of the ON/OFF Switch marked ‘O’
Duty cycle
WARNING
: This product has a duty cycle of 30%.
• After every three minutes of use, the sharpener must be allowed to cool down for seven minutes,
before continuing with another maximum three minutes’ continuous use
• This product is equipped with a thermal cut-out device to protect the motor
• If the tool cuts out, the duty cycle has been exceeded. Switch OFF the tool and allow the motor to
cool down fully. You will then be able to proceed, using the tool in accordance with the 30% duty
cycle
Sharpening HSS drill bits
• The multipurpose sharpener will sharpen high-speed steel drill bits of 3 – 13mm diameter
• When sharpening drill bits of 3-3.5mm diameter, ensure the Top Clamp (12) is installed on the
Drill Bit Clamp with the protruding face directed inwards (Image A)
• When sharpening drill bits of 3.5-13mm diameter, ensure the Top Clamp is installed on the Drill
Bit Clamp with the protruding face directed outwards (Image B)
Preparation:
1. Slide the Drill Bit Sharpening Module into position over the Grinding Wheel (5) on the Motor
Unit
2. Remove the Drill Bit Clamp (11) from the module and loosen the jaw sufficiently to insert the
drill bit
3. Tighten the Drill Bit Clamp just to the point where the drill bit is retained but its position can still
be adjusted
4. Place the Drill Bit Clamp in the Alignment Shoe (11), being sure the Drill Bit Clamp engages the
rails on the Alignment Shoe (Image C)
5. Push the drill bit forward and rotate the bit so that it lays in the ‘V’ Guide with the tip in contact
with the metal end stop and the cutting edges are in contact with the metal sides of the ‘V’
6. Tighten the Drill Bit Clamp to secure the drill bit in this position
7. Remove the Drill Bit Clamp, with the drill bit secured in position, and place it in the Grinding
Shoe (8) ensuring the Drill Bit Clamp engages the rails on the Grinding Shoe
8. Check the cutting edges of the drill bit are in contact with the Grinding Wheel. If not, repeat the
alignment procedure
9. The drill bit is now ready for sharpening with the cutting edges positioned at the correct angle
Sharpening:
1. Switch the tool ON and move the top section of the Drill Bit Sharpening Module from side to side
to sharpen both cutting edges (Image D)
Note
: The amount of sharpening required will depend upon the condition of the cutting edges
2. Switch the tool OFF, remove the Drill Bit Clamp from the Grinding Shoe, and then re-insert it the
other way round in order to sharpen the other side of the cutting edges
3. Repeat the sharpening procedure for an equal amount of time then switch the tool OFF
4. Lift the Drill Bit Clamp out of the Grinding Shoe and check that the leading edges of both flutes
are equally sharp. They should meet exactly in the middle
5. Repeat the sharpening procedure to correct any misalignment as necessary
6. Switch the tool OFF and allow the Grinding Wheel to stop completely before removing the Drill
Bit Sharpening Module
Sharpening chisels and plane irons
• The multipurpose sharpener will sharpen chisels and plane irons of 6 – 51mm width (1/4” – 2”)
Preparation:
1. Slide the Chisel & Plane Sharpening Module into position over the Grinding Wheel (5) on the
Motor Unit
2. Place the blade on the Tool Bed (15) so the side of the chisel or plane iron is adjacent to the lip
on the far edge of the Tool Bed. The magnets will help to secure the blade in position
Note
: For thin chisel blades, fit the Spacer (16) on to the lip, and ensure the chisel is adjacent to
the spacer.
3. Check the angle of the Tool Bed matches the existing bevelled angle on the blade. This is
important to maintain blades at their optimum shaving angle
4. To adjust the angle of the Tool Bed, loosen the Angle Adjustment Knob (13), tilt the Tool Bed to
the correct angle, then tighten the Angle Adjustment Knob to secure the Tool Bed at the correct
angle
5. Check the edge of the blade is in contact with the Grinding Wheel and that the Guard (14) is
fitted. DO NOT use the Chisel & Plane Sharpening Module without the Guard in place
Sharpening:
1. Switch the machine ON, and whilst holding the tool in position on the Tool Bed, move the
Tool Bed back and forth across the Grinding Wheel, using steady pressure and a continuous,
consistent motion (Image E)
2. Do not allow the blade to remain stationary – this will cause uneven sharpening
3. Remove the blade and check the bevelled edge and tip are sharp and even across their entire
width
4. If necessary, continue the sharpening procedure to correct any misalignment
5. Switch the machine OFF and allow the Grinding Wheel to stop completely before removing the
Chisel & Plane Sharpening Module
6. After grinding, it is recommended that you hone the blade on an oil stone
Sharpening knives and scissors
• The multipurpose sharpener will sharpen all straight-edged knives and scissors
• To sharpen knives and scissors, slide the Knife & Scissors Sharpening Module into position over
the Grinding Wheel (5) on the Motor Unit
Sharpening knives:
1 . Switch the tool on
2. Fully insert the knife blade into one of the Knife Sharpening Slots (2), so the cutting edge is
facing the Grinding Wheel (Image F)
3. Bring the blade into contact with the Grinding Wheel and draw it slowly towards you, using light
pressure to keep the blade in contact with the Grinding Wheel throughout the length of the
blade
4. Turn the knife over and insert the blade in the opposite knife sharpening slot. Repeat step 3 to
sharpen the other side of the blade
5. Repeat the sharpening process on each side of the blade in turn until a clean, sharp edge is
attained
6. Switch the sharpener off and allow the grinding wheel to stop completely before removing the
Knife & Scissors Sharpening Module
657946_Manual.indd 6
13/06/2017 14:25
