Silverline 999666, Instruction Manual

Page: 5 / 28

www.silverlinetools.com
5
999666 Rechargeable Torch
Torch Safety
When the torch is switched on, the following must be observed:
• Do not look directly into the lens
• Do not shine into a person's eyes or an animal's eyes
• Do not point the beam at: cars, motorcycles, aircraft, ships or any other
vehicle or machinery that is operated by a person. Bright light can be
blinding and you could cause a serious accident
Unpacking Your Tool
• Carefully unpack and inspect your tool. Fully familiarise yourself with all
its features and functions
• Ensure that all parts of the tool are present and in good condition.
If any parts are missing or damaged, have such parts replaced before
attempting to use this tool
Before Use
IMPORTANT:
The sealed lead acid battery in this product will be drained
from storage. The following steps must be taken to ensure it is charged
correctly. This will maximise the performance and working life of
the battery:
• Press the On/Off Switch (5) and check to see when the torch is On
• NOW MAKE SURE the product is switched OFF. The torch will only charge
in the OFF position
• Plug the Mains Charger (6) in to the mains power supply, and plug the
small end into the charging socket
• Leave to charge for a MINIMUM of 16 hours before first use
NOTE: If the torch fails to charge repeat the above, ensuring that the Switch
(5) is in the OFF position.
Operation
• Switch the torch on or off using the Switch (5)
• The Pistol Handle (4) can be twisted through 90 degrees by pressing the
Handle Lock Button (3)
• Make sure the handle 'clicks' into position and is locked firmly
• To change the angle of the beam when the torch is surface mounted
adjust the Adjustable D-Stand/Handle accordingly
d) Store idle devices out of the reach of children and do not allow
persons unfamiliar with the device or these instructions to
operate it. Electrical devices may be dangerous in the hands of
untrained users.
e) Maintain electrical devices. Check for defects of parts and
any other condition that may affect the device’s operation.
If damaged, have the device repaired before use.
Many accidents
are caused by poorly maintained electrical devices.
f)
Use the device and its accessories in accordance with these
instructions, taking into account the conditions and the task to
be performed. Use of the device for operations different from those
intended could result in a hazardous situation.
Service
a) Have your power tool serviced by a qualified repair person using
only identical replacement parts. This will ensure that the safety of
the power tool is maintained
Battery & Battery Charger
Note: This product features a non-replaceable captive battery.
The following is general safety guidance for charging.
Use the battery charger correctly
• Refer to the section of this manual relating to use of the battery charger
before attempting to charge the battery
• Do not attempt to use the charger with any batteries other than those
supplied. Keep the battery charger clean; foreign objects or dirt may
cause a short or block air vents. Failure to follow these instructions may
cause overheating or fire
• If the supply cord is damaged, it must be replaced by the manufacturer,
its service agent or similarly qualified persons in order to avoid a hazard
Warning: Do not recharge non-rechargeable batteries
Use batteries correctly
• Only charge batteries using the charger provided. Only use batteries
provided with this power tool, or others recommended by the supplier.
Keep batteries clean; foreign objects or dirt may cause a short. Allow
batteries to cool for 15 minutes after charging or heavy use. Failure to
follow these instructions may cause overheating or fire
• When not in use batteries should be stored at room temperature
(approx 20˚C). Ensure that batteries cannot accidentally short in storage.
1
Bulb
2 Lens Ring
3 Handle Lock Button
4 Pistol Handle
5 On/Off Switch
6 Mains Charger
7 12v Charger
8 Adjustable D-Stand/ Handle
Product Familiarisation
999666_Z1MANPRO1.indd 5 04/11/2016 17:17