![background image](http://html.mh-extra.com/html/silverline/321030/321030_quick-manual_1273558009.webp)
Air Sheet Metal Shears
321030
9
silverlinetools.com
Operation
WARNING:
Ensure the material to be cut does not exceed the cutting capacity of this device.
Note:
Always mark the line or shape to be cut on the material.
1. Grip the tool and depress the Speed Control Trigger (3) to start the tool
2. Apply light pressure to move the blades through the material, as shown in Fig. I
Note:
If the device stalls whilst cutting, release pressure on the speed control trigger to turn OFF the
tool. Pull back from the cutting edge. Depress the trigger to restart the cutting process and slowly
engage the cut.
3. Release pressure on the Speed Control Trigger to finish cutting
Note:
This device is designed for cutting straight lines and gradual curves, not 90° corners.
Note:
DO NOT allow the shear to run in ‘idle rotation’ for an extended period of time. This will
shorten its life.
WARNING:
Be aware that air tools may hold residual pressure after use. Always bleed air pressure
from the tool after shutting off air supply.
Accessories
• Accessories for this tool, including spare blades (Centre Shear Blade, Left Shear Blade, and Right
Shear Blade), are available from your Silverline stockist
• Other spare parts can be obtained from your Silverline dealer or www.toolsparesonline.com
Maintenance
WARNING:
Always disconnect from the air supply and depressurise before cleaning or carrying out
any maintenance.
Replacing blades
Note:
Periodically inspect and replace blades as necessary. All three blades are available to purchase
separately (see ‘Accessories’), however, it is recommended to always replace them as a set.
1. Remove the Blade Retaining Hex Bolts (2) using the Hex Key (7)
2. Remove the centre blade first, then the left and right blades and bushing
3. Replace with new blades. Place the bushing between the new left and right blades (see Fig. II),
and insert into the Blade Assembly (1)
4. Insert the three previously removed Blade Retaining Hex Bolts into the body of the blade
assembly, and tighten all three bolts with the hex key
Cleaning
• Keep your tool clean at all times. Dirt and dust will cause internal parts to wear quickly, and
shorten the machine’s service life. Clean the body of your machine with a soft brush, or dry cloth
IMPORTANT:
There is very little that can go wrong with your air tool and it should be noted that
when an air tool fails to work it is generally because the internal workings have corroded due to
dirty, wet air and failure to follow the instructions given below.
Daily maintenance procedure:
Disconnect from the air supply, pour a few drops of oil into the air
intake. Operate the machine at low speed to thoroughly lubricate all internal workings.
• If the machine is in constant use or used for long periods at a time, a combined filter/lubricator
must be fitted. There must be an air filter fitted at all times
• Use air tool oil. DO NOT UNDER ANY CIRCUMSTANCES USE NORMAL ENGINE OIL
• Failure to comply with the operating and maintenance instructions may invalidate the guarantee
Contact
For technical or repair service advice, please contact the helpline on (+44) 1935 382 222
Web:
silverlinetools.com/en-GB/Support
Address:
Toolstream Ltd.
Boundary Way
Lufton Trading Estate
Yeovil, Somerset
BA22 8HZ, United Kingdom
Storage
• Store this tool carefully in a secure, dry place out of the reach of children
• Oil the tool before storing as detailed in the Daily Maintenance instructions
Disposal
• As with other power tools, air tools should not be disposed of with household waste
• Air tools may contain traces of tool oil and other lubricants and so must be recycled accordingly
• Contact your local waste disposal authority for information on the correct way to dispose of power
tools
Problem
Possible Cause
Solution
Tool operating slowly
Pressure incorrect
Set the correct air
pressure according to the
specification
Dirt within the mechanism
Pour oil into air inlet as per
maintenance instructions
Air blockage
Operate tool in short bursts
to clear blockage
Air leak
Check all fittings and hose
for air leaks and correct
issue by re-tightening,
using PTFE tape or
replacing
Blockage in gauze
mesh filter
Remove Quick Connector
(3) and clean mesh filter
Tool seized
Dirt or rust in mechanism
Try ‘Tool operating slowly’
solutions
Dirt or rust in mechanism
Tap tool gently with a
soft mallet
Dirt or rust in mechanism
Free mechanism by
rotating drive manually
when disconnected from
air line
Tool will not stop after
trigger is fully released
Throttle valve O-ring or
valve seat damaged
Have the tool repaired at
an authorised Silverline
service centre
If the above troubleshooting solutions fail, contact your dealer or an authorised
Silverline service centre.
321030_Manual.indd 9
10/12/2019 14:07
Summary of Contents for 321030
