manualshive.com logo in svg

Silicon Laboratories Si446 Series, Manual

Share
Download
Silicon Laboratories Si446 Series Manual Download Page 31

AN625

Rev. 0.1

31

Parameters



FILTER_MATCH_PEND_CLR - If clear, Clear pending FILTER_MATCH interrupt. If set, leave interrupt pending 



FILTER_MISS_PEND_CLR - If clear, Clear pending FILTER_MISS interrupt. If set, leave interrupt pending 



PACKET_SENT_PEND_CLR - If clear, Clear pending PACKET_SENT interrupt. If set, leave interrupt pending 



PACKET_RX_PEND_CLR - If clear, Clear pending PACKET_RX interrupt. If set, leave interrupt pending 



CRC32_ERROR_PEND_CLR - If clear, Clear pending CRC32_ERROR interrupt. If set, leave interrupt pending 



TX_FIFO_ALMOST_EMPTY_PEND_CLR - If clear, Clear pending TX_FIFO_ALMOST_EMPTY interrupt. If set, leave 

interrupt pending 



RX_FIFO_ALMOST_FULL_PEND_CLR - If clear, Clear pending RX_FIFO_ALMOST_FULL interrupt. If set, leave 

interrupt pending 



INVALID_SYNC_PEND_CLR - If clear, Clear pending INVALID_SYNC interrupt. If set, leave interrupt pending 



RSSI_JUMP_PEND_CLR - If clear, Clear pending RSSI_JUMP interrupt. If set, leave interrupt pending 



RSSI_PEND_CLR - If clear, Clear pending RSSI interrupt. If set, leave interrupt pending 



INVALID_PREAMBLE_PEND_CLR - If clear, Clear pending INVALID_PREAMBLE interrupt. If set, leave interrupt 

pending 



PREAMBLE_DETECT_PEND_CLR - If clear, Clear pending PREAMBLE_DETECT interrupt. If set, leave interrupt 

pending 



SYNC_DETECT_PEND_CLR - If clear, Clear pending SYNC_DETECT interrupt. If set, leave interrupt pending 



FIFO_UNDERFLOW_OVERFLOW_ERROR_PEND_CLR - If clear, Clear pending 

FIFO_UNDERFLOW_OVERFLOW_ERROR interrupt. If set, leave interrupt pending 



STATE_CHANGE_PEND_CLR - If clear, Clear pending STATE_CHANGE interrupt. If set, leave interrupt pending 



CMD_ERROR_PEND_CLR - If clear, Clear pending CMD_ERROR interrupt. If set, leave interrupt pending 



CHIP_READY_PEND_CLR - If clear, Clear pending CHIP_READY interrupt. If set, leave interrupt pending 



LOW_BATT_PEND_CLR - If clear, Clear pending LOW_BATT interrupt. If set, leave interrupt pending 



WUT_PEND_CLR - If clear, Clear pending WUT interrupt. If set, leave interrupt pending 

Response



CHIP_INT_STATUS_PEND - If set, CHIP_INT_STATUS interrupt is pending. 



MODEM_INT_STATUS_PEND - If set, MODEM_INT_STATUS interrupt is pending. 



PH_INT_STATUS_PEND - If set, PH_INT_STATUS interrupt is pending. 



CHIP_INT_STATUS - If set, chip status has interrupt pending 



MODEM_INT_STATUS - If set, modem status has interrupt pending 



PH_INT_STATUS - If set, packet handler status has interrupt pending 



FILTER_MATCH_PEND - If set, FILTER_MATCH interrupt is pending. 



FILTER_MISS_PEND - If set, FILTER_MISS interrupt is pending. 



PACKET_SENT_PEND - If set, PACKET_SENT interrupt is pending. 



PACKET_RX_PEND - If set, PACKET_RX interrupt is pending. 



CRC32_ERROR_PEND - If set, CRC32_ERROR interrupt is pending. 



TX_FIFO_ALMOST_EMPTY_PEND - If set, TX_FIFO_ALMOST_EMPTY interrupt is pending. 



RX_FIFO_ALMOST_FULL_PEND - If set, RX_FIFO_ALMOST_FULL interrupt is pending. 



FILTER_MATCH - If set, incoming packet matched filter. 



FILTER_MISS - If set, incoming packet was discarded because filter did not match 



PACKET_SENT - If set, Packet Sent 



PACKET_RX - If set, Packet Received 



CRC32_ERROR - If set, CRC-32 error 

CHIP_PEND

XX FIFO_

UNDERFLOW_

OVERFLOW_

ERROR_PEND 

STATE_

CHANGE_

PEND 

CMD_

ERROR_

PEND 

CHIP_

READY_

PEND 

LOW_BATT_

PEND 

WUT_

PEND 

CHIP_

STATUS

XX FIFO_

UNDERFLOW_

OVERFLOW_

ERROR 

STATE_

CHANGE 

CMD_

ERROR 

CHIP_

READY 

LOW_BATT WUT 

Summary of Contents for Si446 Series

















































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands