Silicon Graphics InfiniteStorage C1104-GP6 System User'S Manual Download Page 49

Page: 49 / 76

System Rear I/O Ports

007-6465-001

ACPI Features

•

Slow blinking LED for suspend state indicator

•

BIOS support for USB keyboard

•

Wake-On-LAN (WOL)

•

Internal/external modem ring-on

•

16 MB SPI AMIBIOS® SM Flash UEFI BIOS

•

Hardware BIOS Virus protection

Onboard I/O

•

Four 3.5-inch disk drive bays supported by an on-chip SATA controller (JBOD and optional
RAID 1 are supported)

•

Two (2) external USB (Universal Serial Bus 3.0) ports (type A)

•

Two (2) external USB 2.0 ports (type A)

•

RJ-45 LAN ports supported by an on-board Intel® Ethernet controller

•

A dedicated (RJ-45) IPMI LAN port

•

One VGA port supported by an Aspeed 2400 graphics controller (with DDR3 memory)

•

One Serial (COM) port

Serverboard Dimensions

Proprietary board format is: 13.05" x 8.15" (331.5 mm x 207 mm).

Summary of Contents for InfiniteStorage C1104-GP6













































































Search results

Summary of Contents for InfiniteStorage C1104-GP6

Reviews:

Related manuals for InfiniteStorage C1104-GP6

Brands by name

Popular brands

Silicon Graphics InfiniteStorage C1104-GP6, System User'S Manual

Search results

Summary of Contents for InfiniteStorage C1104-GP6

Reviews:

Related manuals for InfiniteStorage C1104-GP6

Brands by name

Popular brands