Silicon Graphics InfiniteStorage C1104-GP6 System User'S Manual Download Page 17 | Manualshive

Page: 17 / 76

background image

Server Chassis Features

007-6465-001

5

Server Chassis Features

The following subsections provide a general outline of the main features of the ISS C1104-GP6
chassis.

System Power

The SGI ISS C1104-GP6 1U chassis features a redundant power supply composed of two separate
power modules. This power redundancy feature allows you to replace a failed power supply
without shutting down the system. Note that each power supply provides up to 500 Watts of power
to the system.

Serial ATA Subsystems

The server chassis supports up to four 3.5-in SATA drives. Chassis drives are SATA 3.0
6-Gb/second slots. RAID 1 drives are hot-swappable units and are connected to a backplane that
provides power and control. Note that the operating system you have installed must support RAID
to enable the hot-swap capability of RAID drives. Certain RAID levels may require use of
optional hardware or software to support RAIDed hard disk drives in the server.

Front Control Panel

The control panel on the ISS C1104-GP6 provides you with chassis monitoring and control. LEDs
that indicate system power, HDD activity, network activity and a chassis overheat/fan-fail/ UID
LED. A main power button and a system reset button are also included.

Serverboard and PCIe Subsystem

The ISS C1104-GP6 chassis is an ATX form factor chassis designed to be used in a 1U rackmount
configuration. The serverboard’s I/O backplane supports two standard size (full-height x16) PCIe
cards and one half-height (x8) PCIe card which can offer optional computing solutions. A 15-pin
VGA port, a serial (COM) port, two USB 3.0 and two USB 2.0 ports, two Gigabit LAN ports and
a dedicated RJ-45 IPMI LAN port are also supported.

«
...
15
16
17
18
19
...
»

Summary of Contents for InfiniteStorage C1104-GP6













































































Reviews:

No comments

Related manuals for InfiniteStorage C1104-GP6

Netfinity 1000-8477 21Y

Brand: IBM Pages: 268

SUPERSERVER 1017GR-TF

Brand: Supero Pages: 100

Brand: IBM Pages: 90

UCS Invicta C3124SA

Brand: Cisco Pages: 60

Brand: Cisco Pages: 54

UCS Invicta C3124SA

Brand: Cisco Pages: 40

Brand: Cisco Pages: 132

Brand: Cisco Pages: 46

Brand: Cisco Pages: 35

Brand: Cisco Pages: 188

Brand: Dell Pages: 129

PowerEdge HR675

Brand: Dell Pages: 194

PowerEdge FC630

Brand: Dell Pages: 143

PowerEdge HX574

Brand: Dell Pages: 202

Wyse 5020 P Series

Brand: Dell Pages: 8

Brand: Dell Pages: 2

Brand: Dell Pages: 12

Wyse 5000 Series

Brand: Dell Pages: 8

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands