Silicon Graphics InfiniteStorage C1104-GP6 System User'S Manual Download Page 14

Page: 14 / 76

007-6465-001

1: Introduction

Figure 1-1

and

Figure 1-2

show examples of the 1U server and it’s external components.

Figure 1-1

SGI ISS C1104-GP6 System Front View Example

Figure 1-2

SGI ISS C1104-GP6 System Rear View Example

Note:

Check with your SGI sales or service representative for the latest information on optional

PCIe cards available for this server.

Server control/

status panel

3.5” Disk Drives (4)

Server control/

status panel

Optional DVD drive

VGA Port

Ethernet LAN Ports (2)

COM Port

UID

Power Supplies (2)

IPMI LAN Port

USB Ports 0, 1 (2.0)

USB Ports 2, 3 (3.0)

Low-profile x8 PCIe (3.0) slot

Full-height x16 PCIe (3.0) slots

Summary of Contents for InfiniteStorage C1104-GP6













































































Search results

Summary of Contents for InfiniteStorage C1104-GP6

Reviews:

Related manuals for InfiniteStorage C1104-GP6

Brands by name

Popular brands

Silicon Graphics InfiniteStorage C1104-GP6, System User'S Manual

Search results

Summary of Contents for InfiniteStorage C1104-GP6

Reviews:

Related manuals for InfiniteStorage C1104-GP6

Brands by name

Popular brands