background image

Wireless Camera 

Front & Side Controls 

1. Camera Antenna

 – Sends signals to 

the receiver. 

2. AC Adaptor Jack

 – Plug the AC 

adaptor to the jack for camera’s power 
supply.

 

3. Wall Mounting Bracket

 – Use the 

bracket to mount the camera on a wall or 
other flat surfaces. 

4. IR LEDs

 – Infrared LEDs provide 

viewing in no/low light conditions

   

5. Lens

 – Catches the video in front of 

the lens and transmits video from 
camera to receiver. 

6. PIR Sensor

 – Detects motion in front 

of the lens and emits detection signal to 
transmitter.

 

Bottom Controls

 

7. Microphone

 – Receives sounds from 

the area near the camera, and transmits 
sound from the camera to the receiver. 

 

4

Back Controls 

8. Pair Button

 – The pair button is 

located on the back of the camera, it is 
used to pair the camera with receiver. 

Camera Installation 

Before you install the camera, carefully 
plan where and how it will be positioned, and where you will route the cable that connects the camera to 
the power adaptor. 

Before starting permanent installation, verify its performance by observing the image on the receiver 
when camera is positioned in the same location/position where it will be permanently installed and the 
receiver is placed in the location where it will be used most of the time. 

Summary of Contents for QC3630

















Reviews: