SignaMax FO-065-7732A User Manual Download Page 9 | Manualshive

Page: 9 / 106

SignaMax FO-065-7732A User Manual Download Page 9

Signamax



FO-065-7732A Manageable Gigabit Switch

User’s Manual 7

Front Panel Display

•

POWER

This LED comes on when the switch is properly connected to power and
turned on.

‚

Port Status LEDs

The LEDs are located at the left side of each section, displaying status for
each respective port. Please refer to the following table for more details.

LED

State

Indication

On

A valid network connection established.
LNK stands for LINK.

LNK/ACT

Flashing

Transmitting or receiving data.

ACT stands for ACTIVITY.

On

Connection in full duplex mode.

FDX stands for FULL-DUPLEX.

Flashing

Collision occurred.

COL stands for COLLISION.

FDX/COL

Off

Connection in half-duplex mode.

ƒ

Gigabit Port Status LEDs

The LEDs are located at the left side of each Gigabit module, displaying
status for each respective port. Please refer to the following table for more
details.

«
...
7
8
9
10
11
...
»

Summary of Contents for FO-065-7732A











































































































Reviews:

No comments