SIG E-FORCE ARF Manual Download Page 10 | Manualshive

Page: 10 / 10

SIG E-FORCE ARF Manual Download Page 10

10

WARNING! THIS IS NOT A TOY!

Flying machines of any form, either model-size or full-size, are not toys!
Because of the speeds that airplanes must achieve in order to fly, they are
capable of causing serious bodily harm and property damage if they crash.
IT IS YOUR RESPONSIBILITY AND YOURS ALONE to assemble this
model airplane correctly according to the plans and instructions, to ground
test the finished model before each flight to make sure it is completely
airworthy, and to always fly your model in a safe location and in a safe
manner. The first test flights should only be made by an experienced R/C
flyer, familiar with high performance R/C aircraft.

JOIN THE AMA

The governing body for radio-control model airplanes in the United States
is the ACADEMY OF MODEL AERONAUTICS, commonly called the AMA.
The AMA SAFETY CODE provides guidelines for the safe operation of R/C
model airplanes. While AMA membership is not necessarily mandatory, it
is required by most R/C flying clubs in the U.S. and provides you with
important liability insurance in case your R/C model should ever cause
serious property damage or personal injury to someone else.

ACADEMY OF MODEL AERONAUTICS

5161 East Memorial Drive

Muncie, IN 47302

Telephone: (765) 287-1256

AMA WEB SITE: www.modelaircraft.org

CUSTOMER SERVICE

SIG MANUFACTURING COMPANY, INC. is committed to your success in
both assembling and flying the E-FORCE ARF. Should you encounter any
problem building this kit or discover any missing or damaged parts, please
feel free to contact us by mail or telephone.

SIG MANUFACTURING COMPANY, INC.

401-7 South Front Street

Montezuma, IA 50171-0520

SIG MODELER’S ORDERLINE: 1-800-247-5008

(to order parts)

SIG MODELER’S HOTLINE: 1-641-623-0215

(for technical support)

SIG WEB SITE: www.sigmfg.com

LIMIT OF LIABILITY

The craftsmanship, attention to detail and actions of the builder/flyer of
this model airplane kit will ultimately determine the airworthiness, flight
performance and safety of the finished model. SIG MFG. CO.’s obligation
shall be to replace those parts of the kit proven to be defective or missing.
The user shall determine the suitability of the product for his or her
intended use and shall assume all risk and liability in connection therewith.

E-FORCE LOG BOOK

Date:

Battery Pack:

Comments:

«
...
8
9
10

Summary of Contents for E-FORCE ARF











Reviews:

No comments