Siemens SIWAREX WP321 Operating Instructions Manual Download Page 84

Page: 84 / 132

8.13.1

Specification of tare weight

You can enter a tare weight. If a tare weight is to be applied, it must be enabled with the

corresponding command. The tare weight must not exceed the maximum tare load specified in

data record DR 3.

8.14

DR 30 current process values

Current states and process values in the scales can be monitored using process values and

advanced process values from data record DR 31. Monitoring selected data during

commissioning is extremely useful as it helps you to optimize parameters.

Procedure
● Read data record DR 30 cyclically or on a time-triggered basis
● Display/analyze the required tags
It is not always necessary to cyclically read data record DR 30. If the relevant process tags have

already been selected in data record DR 14 (→ DR 14 SIMATIC interface parameters

(Page 81) ), they are immediately transferred via the I/O interface. In this case, these tags and

all status bits and messages are accessible without data record communication.

Table 8-11

Assignment of data record 30

Variable

Note

Type

Default

Min.

Max.

Data record

number

Contains no. of data record

UINT

Length

Data record length information UINT

Application

Information on which applica‐

tion the data record belongs to

UINT

201

Version identi‐

fier

Information on the current da‐

ta record version

UINT

255

1/4d zero

Set if gross is less than ± 0.25e BIT

9e max

Set if the weight has exceeded

the gross weighing range by

more than 9 display steps (d)

BIT

Tared

Set if tare memory is not equal

to zero

BIT

Manual tare

set (pT)

Set if the tare memory is as‐

signed an external specified

value

BIT

Reserve

BIT

Waiting for

standstill

Set if module is waiting for

standstill to execute command

BIT

Standstill

Set if standstill condition is met BIT

Reserve

BIT

Empty

Set if "Empty" condition is met BIT

Limit value 1

Limit value 1 has responded

BIT

Scale parameters and functions
8.14 DR 30 current process values

SIWAREX WP321

Operating Instructions, 08/2019, A5E33715669A-AD

Summary of Contents for SIWAREX WP321





































































































































Search results

Summary of Contents for SIWAREX WP321

Reviews:

Siemens SIWAREX WP321, Operating Instructions Manual, Page: 84 / 132

Search results

Summary of Contents for SIWAREX WP321

Reviews: