manualshive.com logo in svg

Siemens SIWAREX WP321, Operating Instructions Manual, Page: 32 / 132

Share
Download
Siemens SIWAREX WP321 Operating Instructions Manual Download Page 32

Figure 6-8

Shield connection and shield terminal

6.4

Connection of RS485 serial interface

Devices can be connected to the serial interface RS485 in accordance with the information in 

section Technical data (Page 115).

Table 6-2

Termination of RS485 serial interface

Labeling

Function

Connection pin

RS485: T+

RS485 termi: 

Is used at the physical end of the bus for inserting termi‐

nation jumpers

9

RS485: T-

RS485 termination -: 

Is used at the physical end of the bus for inserting termi‐

nation jumpers 

10

RS485: D+'

RS485 data line +':

Is used at the physical end of the bus for inserting termi‐

nation jumpers and in between for looping through the 

bus cables

11

RS485: D-'

RS485 data line -':

Is used at the physical end of the bus for inserting termi‐

nation jumpers and in between for looping through the 

bus cables 

12

RS485: D+

RS485 data cable +

13

RS485: D-

RS485 data cable -

14

If a SIWAREX WP321 module is connected to SIWATOOL or a Siebert display, insert wire 

jumpers between the T+ and D+' terminals and between the T- and D-' terminals.

Connecting
6.4 Connection of RS485 serial interface

SIWAREX WP321

32

Operating Instructions, 08/2019, A5E33715669A-AD

Summary of Contents for SIWAREX WP321





































































































































Reviews:

No comments