background image

 

Functions 

 

9.18 Operating hours counter in temperature classes 

SITRANS TR200/TR300 
Operating Instructions, 06/2010, A5E01071992-03 

61

 

9.18

 

Operating hours counter in temperature classes 

The SITRANS TR200/TR300 has different operating hours counters. The operating hours 

counters are for monitoring the connected process flows. 

1. Operating hours counter for transmitter electronics 

●  Monitors the number of operating hours that the transmitter has been in continuous 

operation subject to the ambient temperature. 

●  Records the process of operating hours of the transmitter in 9 ranges of ambient 

temperature. 

●  Begins with the first commissioning at the plant. 
●  The user cannot reset or adjust the operating hours counter or temperature ranges. 
●  The operating hours counter is only updated when it is in measuring mode. The operating 

hours counter is not updated in simulation mode. 

2. Operating hours counter for process variable 

●  Monitors the process of the sensor connected to the transmitter in different process 

ranges. 

●  Records the process of operating hours of the process variable in 9 ranges. Subdivision 

takes place subject to the connected sensor and its sensor limits. The user cannot adjust 

the ranges. 

●  The operating hours counter is reset automatically if one of its following parameters is 

changed: 
–  Sensor class 
–  Sensor type 
–  Interface connection 
–  Sensor connection 
–  Sensor factor 

The parameter assignment software SIPROM T for SITRANS TR200 or SIMATIC PDM or 

HART communicator on SITRANS TR300 can read out the operating hours counters. The 

operating hours counters are automatically stored to the non-volatile memory once an hour. 

If the power supply to the device is interrupted, the operating hours counters are available 

upon restarting the device. 

Summary of Contents for sitrans tr300

































































































Reviews: