manualshive.com logo in svg

Siemens SITRANS FC310, Compact Operating Instructions, Page: 5 / 54

Share
Download
Siemens SITRANS FC310 Compact Operating Instructions Download Page 5

Introduction

1

1.1

Purpose of this documentation

These instructions contain all information required to commission and use the device. Read the 

instructions carefully prior to installation and commissioning. In order to use the device 

correctly, first review its principle of operation.
The instructions are aimed at persons mechanically installing the device, connecting it 

electronically, configuring the parameters and commissioning it, as well as service and 

maintenance engineers.

See also

Certificates (Page 51)
Technical support (Page 51)

1.2

Document history

The following table shows major changes in the documentation compared to the previous 

edition. 
The most important changes in the documentation when compared with the respective 

previous edition are given in the following table.

Edition

Note

01/2019

Second edition
● Chapter Technical data (Page 47) updated
● Overall revision of chapters and contents

06/2018

First edition

1.3

Device identification

The FC310 Coriolis flowmeter has 3 nameplate types which show the following information:
● product identification
● product specifications
● certificates and approvals

Note
Identification
Identify your device by comparing your ordering data with the information on the product and 

specification nameplates.

SITRANS FC310

Compact Operating Instructions, 01/2019, A5E44932112-AB

5

Summary of Contents for SITRANS FC310























































Reviews:

No comments