manualshive.com logo in svg

Siemens SITRANS FC310, Compact Operating Instructions, Page: 27 / 54

Share
Download
Siemens SITRANS FC310 Compact Operating Instructions Download Page 27

Connecting

4

4.1

Basic safety notes

WARNING

Unsuitable cables, cable glands and/or plugs
Risk of explosion in hazardous areas.
● Use only cable glands/plugs that comply with the requirements for the relevant type of 

protection.

● Tighten the cable glands in accordance with the torques specified in Technical data 

(Page 47).

● Close unused cable inlets for the electrical connections.
● When replacing cable glands, only use cable glands of the same type.
● After installation, check that the cables are seated firmly.

WARNING

Incorrect conduit system
Risk of explosion in hazardous areas as result of open cable inlet or incorrect conduit system.
● In the case of a conduit system, mount a spark barrier at a defined distance from the device 

input. Observe national regulations and the requirements stated in the relevant approvals.

See also

Technical data (Page 47)

WARNING

Hazardous contact voltage
Risk of electric shock in case of incorrect connection.
● For the electrical connection specifications, refer to the information in Technical data 

(Page 47).

● At the mounting location of the device observe the applicable directives and laws for 

installation of electrical power installations with rated voltages below 1000 V.

SITRANS FC310

Compact Operating Instructions, 01/2019, A5E44932112-AB

27

Summary of Contents for SITRANS FC310























































Reviews:

No comments