manualshive.com logo in svg

Siemens SITRANS FC310, Compact Operating Instructions, Page: 22 / 54

Share
Download
Siemens SITRANS FC310 Compact Operating Instructions Download Page 22

NOTICE
Incorrect mounting
The device can be damaged, destroyed, or its functionality impaired through improper 

mounting.
● Before installing ensure there is no visible damage to the device.
● Make sure that process connectors are clean, and suitable gaskets and glands are used.
● Mount the device using suitable tools. Refer to the information in Technical data 

(Page 47).

3.2

Installation instructions

CAUTION

Electromagnetic fields
Do not install the flowmeter in the vicinity of strong electromagnetic fields, for example near 

motors, variable frequency drives, transformers etc.   

Upstream / downstream

● No pipe run requirements, that is straight inlet/outlet sections, are necessary.
● Avoid long drop lines downstream from the sensor to prevent process media separation 

causing air / vapor bubbles in the tube (min. back pressure: 0.2 bar).

● Avoid installing the flowmeter immediately upstream of a free discharge in a drop line.

Installing/mounting
3.2 Installation instructions

SITRANS FC310

22

Compact Operating Instructions, 01/2019, A5E44932112-AB

Summary of Contents for SITRANS FC310























































Reviews:

No comments