manualshive.com logo in svg

Siemens SITRANS FC310, Compact Operating Instructions, Page: 42 / 54

Share
Download
Siemens SITRANS FC310 Compact Operating Instructions Download Page 42

WARNING

Humid environment
Risk of electric shock.
● Avoid working on the device when it is energized.
● If working on an energized device is necessary, ensure that the environment is dry.
● Make sure when carrying out cleaning and maintenance work that no moisture penetrates 

the inside of the device.

WARNING

Enclosure open
Risk of explosion in hazardous areas as a result of hot components and/or charged capacitors 

inside the device. 
To open the device in a hazardous area:
1. Isolate the device from power.
2. Observe the wait time specified in Technical data (Page 47) or on the warning sign before 

opening the device.

3. Visually inspect sensor inlet and outlet.
Exception: Devices exclusively having the type of protection "Intrinsic safety Ex i" may be 

opened in an energized state in hazardous areas.

WARNING

Improper connection after maintenance
Risk of explosion in areas subject to explosion hazard.
● Connect the device correctly after maintenance.
● Close the device after maintenance work.
Refer to Technical data (Page 47).

WARNING

Hot, toxic or corrosive process media
Risk of injury during maintenance work.
When working on the process connection, hot, toxic or corrosive process media could be 

released.
● As long as the device is under pressure, do not loosen process connections and do not 

remove any parts that are pressurized.

● Before opening or removing the device ensure that process media cannot be released.

Service and maintenance
6.3 Maintenance and repair work

SITRANS FC310

42

Compact Operating Instructions, 01/2019, A5E44932112-AB

Summary of Contents for SITRANS FC310























































Reviews:

No comments