Siemens SINUMERIK ONE NCU 1740 Equipment Manual Download Page 38

Page: 38 / 164

7-segment display

Meaning

Before loading the kernel

Before starting the kernel

Booting the basic system

7-segment display

Meaning

Basic initializations

Cleaning up and preparing the file system

The name is set and the loopback interface configured.

Starting the system logging
Starting the CFS class 1, provide the network interfaces.

Initializing the network interfaces and the firewall

Starting the time server (ntpd)

Starting the SSH server (generate a host key if one is still not available).

Starting the FTP server

Starting the TCU services (TFTP, VNC)

Partitioned: The system performs a partitioning operation.

NRK/NCK power up

7-segment display

Meaning

Not applicable.

Debugger was initialized.

NRK operating system was successfully activated.

NRK operating system has booted, init task is being processed (→ the appli‐
cation boots).

1 or 2

SD card and NVRAM data do not match. To resolve this problem, a general
reset is required by booting with switch position 1 or 2.

Operation

7-segment display

Meaning

with flashing point: The control is in cyclic operation and the cycles are active.

4.4.4

Start-up and mode selector switch

The NCU is equipped with an NCK rotary coding switch and a PLC mode selector switch in the
form of a toggle switch with three settings:

Description
4.4 Operator control and display elements

NCU 1740

Equipment Manual, 10/2021, A5E51087503B AA

Summary of Contents for SINUMERIK ONE NCU 1740





































































































































































Search results

Summary of Contents for SINUMERIK ONE NCU 1740

Reviews:

Related manuals for SINUMERIK ONE NCU 1740

Brands by name

Popular brands

Siemens SINUMERIK ONE NCU 1740, Equipment Manual

Search results

Summary of Contents for SINUMERIK ONE NCU 1740

Reviews:

Related manuals for SINUMERIK ONE NCU 1740

Brands by name

Popular brands