Siemens SINUMERIK ONE NCU 1740 Equipment Manual Download Page 100

Page: 100 / 164

LED

Color

Status

Description

Off

Electronics power supply outside the permissible tolerance range, NX is
not ready to run.

Green

Continuous light

CU_LINK is ready for communication and cyclic communication is running.

Flashing light 0.5 Hz

CU_LINK is ready for communication and no cyclic communication is run‐
ning.

Red

Continuous light

At least one CU_LINK fault is present.
CU_LINK not ready for operation (e.g. after switching on)

RESET button

The RESET button is on the front of the module under the cover.

Note

When the button is actuated, the locally connected drive systems are brought to a standstill
without feedback with the control. This means, the drive and control run asynchronously once
the drive has successfully ramped up.

Connectable components
12.1 NX10.3/NX15.3

NCU 1740

100

Equipment Manual, 10/2021, A5E51087503B AA

Summary of Contents for SINUMERIK ONE NCU 1740





































































































































































Search results

Summary of Contents for SINUMERIK ONE NCU 1740

Reviews:

Related manuals for SINUMERIK ONE NCU 1740

Brands by name

Popular brands

Siemens SINUMERIK ONE NCU 1740, Equipment Manual

Search results

Summary of Contents for SINUMERIK ONE NCU 1740

Reviews:

Related manuals for SINUMERIK ONE NCU 1740

Brands by name

Popular brands