Siemens Simotion TM 121C Applications Manual Download Page 23 | Manualshive

Page: 23 / 76

background image

Safety components

© Siemens AG 2003 All Rights Reserved
SIMOTION Safety Unit (AP) - Edition 06.2003

3-23

Comment

If the EMERGENCY OFF or the "Safety guard with restart inhibit" is selected, a
flashing fault lamp or, optionally, a separate alarm lamp (parameterizable)
indicates that the system is ready for acknowledgement.

Figure 3-3 Safety gate safety functions

Note on safety gate with manual acknowledgement

Both contacts must be activated to open the safety gate. If only one contact is
activated and reclosed, an alarm is output with a continuous light. In this case,
both contacts will then have to be opened and reclosed.

The continuous light goes out after both contacts have been properly opened.
When the contacts are closed, a flashing signal indicates that the safety gate is
ready for acknowledgement. After the acknowledge button has been activated,
the machine is again ready to be started.

For safety gates without acknowledgement, there is no display if only one contact
is opened and reclosed due to an operation error. The problem is eliminated by
completely opening and reclosing the gate.

Figure 3-4 Engaging lock safety functions

«
...
21
22
23
24
25
...
»

Summary of Contents for Simotion TM 121C













































































Reviews:

No comments

Related manuals for Simotion TM 121C

Brand: Wansview Pages: 2

MagnaLatch ALERT

Brand: D&D Technologies Pages: 2

Brand: U-Prox Pages: 3

Brand: Channel Vision Pages: 2

SAPPHIRE COMPACT 309150001

Brand: Hygood Pages: 6

Brand: CAMERA LINK Pages: 36

Brand: CP Electronics Pages: 4

D-TECT GJD360/AM

Brand: D-tect Systems Pages: 7

Brand: Idis Pages: 20

Brand: R&TTE Pages: 6

ELI-SIP2-APTZ8-R30X

Brand: e-Line Technology Pages: 42

Brand: Messoa Pages: 20

Brand: DW Pages: 80

Brand: P&E Pages: 2

Brand: Profort Pages: 2

EN1260EchoStream

Brand: Inovonics Pages: 2

Mobile SMS Guard 300

Brand: Marmitek Pages: 52

IS-NIRB3TSC130 Series

Brand: Eagleye Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands