Siemens SIMOGEAR 2KJ40 Operating Instructions Manual Download | Manualshive

Page: 18 / 148

background image

Technical description

2.5 Surface treatment

BA 2030 (2KJ4)

16

Operating Instructions, 07/2020, A5E50009094A/RS-AL

2.5

Surface treatment

2.5.1

General information on surface treatment

All paint finishes are sprayed on.

WARNING

Danger due to electrostatic discharge

For paint finishes in explosion group III, the paint can be electrostatically charged as a result

of intensive dust accumulation or processes with high levels of electrostatic charging.
Risk of explosion as a result of processes with high levels of electrostatic charging.
Minimize the risk of electrostatic charging by applying effective measures according to

IEC 60079-32-1.

NOTICE
Failure of the external protection

If the paint finish is damaged, the geared motor may corrode.
Do not damage the paint finish.

Note

Information about the ability to be repainted does not guarantee the quality of the paint

product supplied by your supplier.
Only the paint manufacturer is liable for the quality and compatibility.

Note

C1 paints are not suitable for ambient air temperature below -20 °C.

«
...
16
17
18
19
20
...
»

Summary of Contents for SIMOGEAR 2KJ40





















































































































































Reviews:

No comments

Related manuals for SIMOGEAR 2KJ40

Brand: Aerotech Pages: 120

Brand: National Instruments Pages: 44

Brand: IBM Pages: 54

Brand: Danfoss Pages: 158

Brand: Newport Pages: 41

Brand: Vacon Pages: 82

Super-writemaster SH-S203N

Brand: Samsung Pages: 2

Super-writemaster SH-S203D

Brand: Samsung Pages: 2

Brand: Samsung Pages: 10

Brand: Samsung Pages: 15

SE-S084C - DVD±RW / DVD-RAM Drive

Brand: Samsung Pages: 1

Brand: Samsung Pages: 16

Brand: Samsung Pages: 25

writemaster SE-S164L

Brand: Samsung Pages: 28

Brand: Samsung Pages: 21

Brand: Samsung Pages: 25

Brand: Samsung Pages: 20

Brand: Samsung Pages: 33

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands