Siemens SIMATIC NET RUGGEDCOM RST2228 Installation Manual Download Page 44

Page: 44 / 58

Technical Specifications

This section provides important technical specifications related to the device.

5.1

Power Supply Specifications

Note

When determining cable lengths, make sure the minimum input voltage for the pow-

er supply is provided at the power source.

Note

Use the internal fuse rating to determine the size of the external circuit breaker/fuse.

Input Range

Power Sup-

ply Type

Min

Max

Internal

Fuse Rating

Maximum

Power Con-

sumption

Wire Gage

12 VDC (Single)

10.5 VDC

15 VDC

12 A

77 W

#14 AWG

24 VDC (Single)

13 VDC

36 VDC

10 A

72 W

#14 AWG

48 VDC (Single)

36 VDC

72 VDC

5 A

72 W

#16 AWG

88 VDC

300 VDC

77 W/ 76W

High Volt-

age AC/DC

85 VAC

264 VAC

3.15 A

75 W/ 75W

#16 AWG

Based on nominal input voltages and 60W output load.

Rated at frequency range 47Hz - 63Hz.

5.2

PoE Power Supply Specifications

The RUGGEDCOM RST2228P adheres to the following power output and IEEE specifi-

cations depending on the input voltage supplied to the device.

CAUTION

Electrical hazard — risk of damage to the device. Do not connect or disconnect the

POE power terminal block when the POE power source is on.

Power In

Voltage Range

Internal

Fuse Rating

Power Out

Wire Gage

51-57 VDC

12 A Maximum

50-57 VDC, 60 W per Port

Maximum (IEEE 302.at)

#18-#12 AWG

RUGGEDCOM RST2228P

Installation Manual, 12/2019, C79000-G8976-1403-05

Summary of Contents for SIMATIC NET RUGGEDCOM RST2228



























































Search results

Summary of Contents for SIMATIC NET RUGGEDCOM RST2228

Reviews:

Related manuals for SIMATIC NET RUGGEDCOM RST2228

Brands by name

Popular brands

Siemens SIMATIC NET RUGGEDCOM RST2228, Installation Manual

Search results

Summary of Contents for SIMATIC NET RUGGEDCOM RST2228

Reviews:

Related manuals for SIMATIC NET RUGGEDCOM RST2228

Brands by name

Popular brands