manualshive.com logo in svg

Siemens SIMATIC ET 200SP F-AI 4xI 0(4) 20mA 2-/4-wire HF Series, Manual

Share
Download
Siemens SIMATIC ET 200SP F-AI 4xI 0(4) 20mA 2-/4-wire HF Series Manual Download Page 54

Interrupts/diagnostic messages 

 

6.1 Status and error display 

 

Analog input module F-AI 4xI 0(4)..20mA 2-/4-wire HF (6ES7136-6AA00-0CA1) 

54

 

Manual, 08/2018, A5E41448857-AB 

DIAG LED 

Table 6- 1 

Error display of the LED DIAG 

DIAG 

Meaning 

 

Off 

Backplane bus supply of the ET 200SP not okay 

 

Flashing 

Module parameters not configured 

 

On 

Module parameters configured and no module diagnostics 

 

Flashing 

•

 

Module parameters configured and module diagnostics 

•

 

Operation in S7-1200/1500 F-CPUs: At least one channel is waiting for a user 

acknowledgment. 

 

Flashing 

•

 

Operation in S7-1200/1500 F-CPUs: The F-module is waiting for a user ac-

knowledgment after a module fault. 

•

 

Operation in S7-300/400 F-CPUs: The F-module is waiting for a user acknowl-

edgment. 

Channel status/channel fault LED 

Table 6- 2 

Status display of the LEDs channel status / channel error 

Channel status  Channel fault  Meaning 

 

Off 

 

Off 

Channel deactivated or supply voltage L+ missing. 

 

On 

 

Off 

Channel activated and no channel diagnostics 

 

Off 

 

On 

Channel activated and channel diagnostics 

/

 

Alternately flashing 

At least one channel is waiting for a user acknowledgment. 

Summary of Contents for SIMATIC ET 200SP F-AI 4xI 0(4) 20mA 2-/4-wire HF Series










































































Reviews:

No comments

Brands by name

Popular brands

Load more brands