manualshive.com logo in svg

Siemens SIMATIC ET 200SP F-AI 4xI 0(4) 20mA 2-/4-wire HF Series, Manual

Share
Download
Siemens SIMATIC ET 200SP F-AI 4xI 0(4) 20mA 2-/4-wire HF Series Manual Download Page 3

 

Analog input module F-AI 4xI 0(4)..20mA 2-/4-wire HF (6ES7136-6AA00-0CA1) 
Manual, 08/2018, A5E41448857-AB 

3

 

Preface 

 

 

Purpose of the documentation 

This manual supplements the system manual Distributed I/O System ET 200SP 

(

http://support.automation.siemens.com/WW/view/en/58649293

).  

Functions that affect the system in general are described in the system manual. 
The information in this manual and the system/function manuals provide support when you 

commission the system. 
A description of the F-system SIMATIC Safety can be found in the programming and 

operating manual SIMATIC Safety – Configuring and Programming 

(

http://support.automation.siemens.com/WW/view/en/54110126

). 

Conventions 

CPU: When the term "CPU" is used hereafter, it refers to both the CPUs of the S7-

1200/1500 automation system and CPUs of the ET 200SP distributed I/O system. 
STEP 7: In this documentation, "STEP 7" is used as a synonym for all versions of the 

configuration and programming software " (STEP 7 TIA Portal)". 
Note the following identified notes: 

 

 

Note 
A note includes important information on the product described in the documentation, on 

handling the product or on the part of the documentation to which you ought to pay special 

attention. 

 

Standards 

You can find a dated reference to the respective standards in the certificate 

(

https://support.industry.siemens.com/cs/ww/en/view/57141281

) or in the EC Declaration of 

Conformity (

https://support.industry.siemens.com/cs/ww/en/view/71764057

) for the F-

module. 

Certified versions 

You can find the certified product and firmware versions in annex 1 of the report on the TÜV 

certificate (

https://support.industry.siemens.com/cs/ww/en/view/57141289

).  

Summary of Contents for SIMATIC ET 200SP F-AI 4xI 0(4) 20mA 2-/4-wire HF Series










































































Reviews:

No comments

Brands by name

Popular brands

Load more brands