manualshive.com logo in svg

Siemens SIMATIC ET 200SP F-AI 4xI 0(4) 20mA 2-/4-wire HF Series, Manual

Share
Download
Siemens SIMATIC ET 200SP F-AI 4xI 0(4) 20mA 2-/4-wire HF Series Manual Download Page 53

 

Analog input module F-AI 4xI 0(4)..20mA 2-/4-wire HF (6ES7136-6AA00-0CA1) 
Manual, 08/2018, A5E41448857-AB 

53

 

 

Interrupts/diagnostic messages 

6 

6.1

 

Status and error display 

LED display 

The following figure shows the LED display of the F-AI 4xI 0(4)..20mA 2-/4-wire HF. 

 

①

 

DIAG (green/red) 

②

 

Channel status (green) 

③

 

Channel fault (red) 

④

 

PWR (green) 

Figure 6-1 

LED display 

Meaning of the LED displays 

The following tables show the meaning of the status and error displays. Remedies for 

diagnostics alarms can be found in section Diagnostic messages (Page 58). 

 

 

WARNING 

The DIAG LED and the channel status and channel fault LEDs of the outputs are not 

designed as safety-related LEDs and therefore may not be evaluated for safety-related 

activities. 

 

Summary of Contents for SIMATIC ET 200SP F-AI 4xI 0(4) 20mA 2-/4-wire HF Series










































































Reviews:

No comments

Brands by name

Popular brands

Load more brands