Siemens SIMATIC EM 148-FC Manual Download Page 4

Page: 4 / 76

EM 148-FC

Frequency Converter

A5E00065321-03

Certification, recognition, approval

The EM 148-FC frequency converter has the following certification:

CSA certification:

Underwriters Laboratories Inc. in accordance with

UL 508 (Industrial Control Equipment)

CSA C22.2 No. 142 (Process Control Equipment)

CE marking

The EM 148-FC frequency converter fulfills the requirements and protection
objectives of the following EC directives:

73/23/EEC (low-voltage directive)

89/336/EEC (EMC directive)

Australian C-Tick mark

The EM 148-FC frequency converter fulfills the requirements of the
AS/NZS 2064 standard (Australia and New Zealand).

Standards

The EM 148-FC frequency converter fulfills the requirements and criteria of
IEC 61131-2.

The EM 148-FC frequency converter is based on the
IEC 61784-1:2002 Ed1 CP 3/1 standard.

Summary of Contents for SIMATIC EM 148-FC













































































Search results

Summary of Contents for SIMATIC EM 148-FC

Reviews:

Related manuals for SIMATIC EM 148-FC

Brands by name

Popular brands

Siemens SIMATIC EM 148-FC, Manual

Search results

Summary of Contents for SIMATIC EM 148-FC

Reviews:

Related manuals for SIMATIC EM 148-FC

Brands by name

Popular brands