Siemens SENTRON 3WL Function Manual Download

Page: 25 / 146

Description of blocks

3.2 Driver module DRV_3WL

Library SENTRON 3WL / 3VL for SIMATIC PCS 7
Function Manual, 11/2008, A5E02316914A-01

3.2.2

Called blocks

The block calls the following blocks:

SFB35  ALARM_8P
SFB52  RDREC
SFB53  WRREC
SFC1

READ_CLK

SFC6

RD_SINFO

SFC20 BLKMOV
SFC21 FILL

3.2.3

Function

The DRV_3WL block is used for measurement acquisition and control and it forms the

interface to the OS.

Automatic / manual mode switch over

Automatic and manual mode are available for operating the driver block. When in manual

mode, the user can control the circuit breaker position (ON / OFF) of the faceplate in WinCC.

When in automatic mode, the corresponding buttons are locked (cannot be operated) in the

faceplate and the circuit breaker is controlled by input parameters which can be connected in

the CFC (AUTO_ON / AUTO_OFF) and therefore by the AS program.
The user can define the mode in which the block is to run in the faceplate or in a block

parameter (AUT_L).
The setting at the LIOP_SEL input determines which of the parameters is currently active.

NOTICE

If an error occurs (monitoring error, Local turn off, Tripped) the block changes to Forced

manual. If the pending error state is acknowledged with one of the RESET buttons, the

block goes into the specified mode again.
If Automatic mode is specified by the AS program (LIOP_SEL = 1, AUT_L = 1) the

commands present at AUTO_ON or AUTO_OFF are always output.
Under certain circumstances this means that resetting error states may cause a switching

operation of the circuit breaker. If this is not desired the user must configure the AS

program accordingly.

Summary of Contents for SENTRON 3WL



















































































































































Search results

Summary of Contents for SENTRON 3WL

Reviews:

Related manuals for SENTRON 3WL

Brands by name

Popular brands

Siemens SENTRON 3WL, Function Manual

Search results

Summary of Contents for SENTRON 3WL

Reviews:

Related manuals for SENTRON 3WL

Brands by name

Popular brands