Siemens SENTRON 3WL Function Manual Download Page 102

Page: 102 / 146

Description of blocks

3.3 Driver module DRV_3VL

Library SENTRON 3WL / 3VL for SIMATIC PCS 7

100

Function Manual, 11/2008, A5E02316914A-01

Message block

Message

number

Message text

Message class

Perform visual inspection on main contacts

Immediate maintenance of main contacts

Monitoring error

AS Control System

Fault

Forbidden switching command for auto mode - switching command

ignored

AS Control System

Fault

Auxiliary values

EV_ID

Auxiliary value

Block parameters

AUX_PR01

AUX_PR02

AUX_PR03

AUX_PR04

AUX_PR05

AUX_PR06

AUX_PR07

AUX_PR08

AUX_PR09

MSG_EVID1

MSG_EVID2

AUX_PR10

3.3.5

Assignment of the cyclic process image

Only basic type 1 is supported.

NOTICE

This allocation does not match the default allocation of basic type 1 for a VL device. Under

certain circumstances, the allocation in the device therefore has to be adjusted. The bytes

which deviate from the default allocation are shown in

italics.

The max. current in the phase with maximum load, which can be found at byte 8 / 9 by

default, is calculated inside the block.

Name

Inputs

Outputs

0 / 1

Control bytes

0 / 1

Binary status information

2 / 3

Current in phase 1

4 / 5

Current in phase 2

6 / 7

Current in phase 3

8 / 9

Current in neutral conductor

Summary of Contents for SENTRON 3WL



















































































































































Search results

Summary of Contents for SENTRON 3WL

Reviews:

Related manuals for SENTRON 3WL

Brands by name

Popular brands

Siemens SENTRON 3WL, Function Manual

Search results

Summary of Contents for SENTRON 3WL

Reviews:

Related manuals for SENTRON 3WL

Brands by name

Popular brands