Siemens SCALANCE X-100 Operating Instructions Manual Download Page 29

Page: 29 / 78

Assembly

4.2 Types of installation

SCALANCE X-100
Operating Instructions, 12/2016, A2B00060666-08

Note
During installation and operation, keep to the installation guidelines and safety notices

described in this document and in the system manuals "Industrial Ethernet / PROFINET

Industrial Ethernet" and "Industrial Ethernet / PROFINET passive network components".
You will find information on the system manuals in the section "AUTOHOTSPOT", in "Further

documentation".

4.2

Types of installation

The devices can be installed in the following ways:

●

Installation on a 35 mm DIN rail

●

Installation on a SIMATIC S7-300 standard rail

●

Wall mounting

WARNING

If a device is operated in an ambient temperature between 50

℃

and 75

℃

, the

temperature of the device housing may be higher than 70 °C. The device must therefore be

installed so that it is only accessible to service personnel or users that are aware of the

reason for restricted access and the required safety measures at an ambient temperature

of 50

℃

to 75

℃

Installation clearance
Keep to the minimum clearances so that the convection ventilation of the device is not

blocked.

●

Below at least 10 cm

●

Above at least 10 cm

4.3

Installation on a DIN rail

Installation

To install the device on a 35 mm DIN rail complying with DIN EN 50022, follow the steps

below:
1.

Place the second housing guide of the device on the top edge of the DIN rail.

Press the device down against the DIN rail until the spring catch locks in place.

Fit the connectors for the power supply. See also section "Power supply (Page 37)".

Summary of Contents for SCALANCE X-100















































































Search results

Summary of Contents for SCALANCE X-100

Reviews:

Related manuals for SCALANCE X-100

Brands by name

Popular brands

Siemens SCALANCE X-100, Operating Instructions Manual

Search results

Summary of Contents for SCALANCE X-100

Reviews:

Related manuals for SCALANCE X-100

Brands by name

Popular brands