Siemens SCALANCE X-100 Operating Instructions Manual Download Page 22

Page: 22 / 78

Description of the device

3.3 TP ports (twisted pair)

SCALANCE X-100

Operating Instructions, 12/2016, A2B00060666-08

Note
Permitted cable lengths
TP cords or TP-XP cords with a maximum length of 10 m can be connected to the TP port

with the RJ-45 jack.
With the IE FC cables and IE FC RJ-45 plugs 180, an overall cable length of a maximum of

100 m is permitted between two devices depending on the cable type.

Autonegotiation

With the autonegotiation mechanism, repeaters and end devices can automatically

determine the transmission speed and the transmission mode of the partner port. This

makes it possible to configure different devices automatically.
Two components connected to a link segment can exchange information about the data

transfer and can adapt their settings to each other. The mode with the highest possible

speed is set.

Note
Devices not supporting autonegotiation must be set permanently to 100 Mbps half duplex or

10 Mbps half duplex.

Note
The IE switches of the SCALANCE X-100 product line are plug-and-play devices that require

no settings during commissioning.

Auto polarity exchange

If the pair of receiving cables is connected incorrectly (RD+ and RD- interchanged), the

polarity is adapted automatically.

MDI / MDI-X autocrossover function

With the MPI/MDI-X autocrossover function, the send and receive contacts of an Ethernet

port are assigned automatically. The assignment depends on the cable with which the

communications partner is connected. This means that it does not matter whether the port is

connected using a patch cable or crossover cable. This prevents malfunctions resulting from

mismatching send and receive wires. This makes installation much easier for the user.

Summary of Contents for SCALANCE X-100















































































Search results

Summary of Contents for SCALANCE X-100

Reviews:

Related manuals for SCALANCE X-100

Brands by name

Popular brands

Siemens SCALANCE X-100, Operating Instructions Manual

Search results

Summary of Contents for SCALANCE X-100

Reviews:

Related manuals for SCALANCE X-100

Brands by name

Popular brands