manualshive.com logo in svg

Siemens POWERMOBIL, Manual, Page: 27 / 36

Share
Download
Siemens POWERMOBIL Manual Download Page 27

Installation

3 - 7

Siemens AG

 

SPR2-240.841.01

Page 7 of 10

POWERMOBIL

Medical Solutions

Rev. 01

05.03

CS PS 24

 

 

POWERPHOS

3

•

Run the cables in the POWERPHOS C-arm segment so that the cables are not crushed 
when inserting the POWERPHOS.

•

Run the loose contacts to the plug Z66 X1, and reinsert them (Fig. 17). 
Tie the cables using cable ties.

•

Reinsert the POWERPHOS in the C-arm segment. Make sure that the cables are not 
crushed.

•

 

Screw the two inverter connectors back on. Tighten the nuts with a torque of 4.8 Nm.

•

Fasten the protective ground wires.

•

Connect all plugs to the POWERPHOS.

•

Connect the collimator plug. 

•

Attach the sterile cover above the collimator.

•

If applicable, assemble the DIAMENTOR dose measuring chamber with insulating disk 
and attach it.

•

Attach the two cable clamps (1/Fig. 18). Make sure that the cable shields makes good 
ground contact.

•

Fit the fan assembly, and connect it observing the connection order as previously noted.

•

Tie or attach all cables using cable ties.

•

Fasten the POWERPHOS to the C-arm. Make sure that the screws are tightened evenly.

Fig. 17

Fig. 18

t

Summary of Contents for POWERMOBIL





































Reviews:

No comments