Siemens OCI600 User Manual Download Page 59

Page: 59 / 72

59/72

Building Technologies

User Manual OCI600

74 319 0002 0 c

HVAC Products

Communication and delivery of alarms

15.07.2005

5.4.2 Sending alarms to the ACS7…

connected via modem

1. If there is a direct connection between PC and OCI600,

cut it.

2. Connect your modem to the OCI600 and check power

supply and wiring to the OCI600 and the telecommuni-

cation network.

3. On the OCI600, on line number 11 of operating card 3,

set the following parameter:

1 = communication via modem.

4. Connect your second modem to the PC and check power

supply and wiring to the telecommunication network and

the COM port.

5. Start

ACS Alarm

via the

ACS Alarm

icon on your desk-

top or via

Start > Programs > ACS > ACS Alarm

6. Open

the

Extras > Connections…

menu.

7. Select the line with your modem entry and close by choo-

sing “Supervise“ and “OK“.

8. Create a new plant, if necessary.

9. Start with ACS Operation – [Popcard].

Note:

The entire setup can be made with ACS Service.

Opening a communication via modem is only possible

with ACS Operation.

10. From the ACS7.. menu, select

Plant > Plant proper-

ties…

11. Choose

Continue

to go to the

Communication

menu.

12. Go to “Connection“ to select your modem.

13. Enter your plant’s phone number in the “Phone no.

plant:“ field.

Important:

The phone number is possibly preceded by

an 0 for an outside line.

14. Choose menu item

Plant > Connect.

15. Status window “Connection information“ appears. This

window shows the current state of communication build-

up. When the window disappears, communication is

opened.

Procedure

Note on ACS

Service and

ACS Operation

Summary of Contents for OCI600









































































Search results

Summary of Contents for OCI600

Reviews:

Related manuals for OCI600

Brands by name

Popular brands

Siemens OCI600, User Manual

Search results

Summary of Contents for OCI600

Reviews:

Related manuals for OCI600

Brands by name

Popular brands