Siemens OCI600 User Manual Download Page 52

Page: 52 / 72

52/72

Building Technologies

User Manual OCI600

74 319 0002 0 c

HVAC Products

Communication and delivery of alarms

15.07.2005

When an analog modem is installed, the Universal Computer

Protocol (UCP) can be used for SMS messages, or the Telo-

cator Alphanumeric Input Protocol (TAP) for SMS. TAP is

used for pager messages.

In the case of an ISDN modem, UCP is used for SMS mes-

sages, or TAP for SMS. TAP is used for pager messages.

OCI600 does not support the original AT+ Protocol of GSM

modems for sending SMS and pager messages.

With GSM modems, the UCP of an

analog connection

can

be used for SMS messages, or TAP can be used for SMS of

analog connection.

For pager messages, the TAP num-

ber of an

analog connection

is used.

For selected countries, the following overview gives the rele-

vant numbers. For the numbers of other countries, contact

your telephone provider.

Type of message SMS

Protocol

UCP (Provider: Mobistar)

Phone number n 495955205

Type of alarm

receiver

Mobile phone (SMS)

Type of message SMS

Protocol

UCP or TAP (Provider: Tele

Danmark)

Phone number n 43625250

Type of alarm

receiver

Mobil Telefon (SMS)

Belgium

+32

Denmark

+45

Summary of Contents for OCI600









































































Search results

Summary of Contents for OCI600

Reviews:

Related manuals for OCI600

Brands by name

Popular brands

Siemens OCI600, User Manual

Search results

Summary of Contents for OCI600

Reviews:

Related manuals for OCI600

Brands by name

Popular brands