Siemens MULTIMOBIL 5C Troubleshooting Manual Download Page 4

Page: 4 / 74

Service Instructions

Multimobil 5C

Siemens Ltd. Med India

Version 5.0

Page 3 of 73

5.3.2

Checking the Filament frequency ...................................................................................... 24

5.3.3

Filament current measurement.......................................................................................... 24

5.3.4

Checking of kV and mAs values ........................................................................................ 24

5.4

UTOMATIC

OSAGE

EGULATION

............................................................................................ 26

5.4.1

ADR Stop Mode (Manual).................................................................................................. 26

5.5

EPLACING THE SINGLE TANK

.................................................................................................... 27

5.5.1

Replacing the collimator..................................................................................................... 27

5.5.2

Aligning the X-ray field to Image Intensifier ....................................................................... 27

CCU AND CAMERA CONTROL ............................................................................................... 29

6.1

INTRODUCTION.................................................................................................................... 29

6.2

RATINGS................................................................................................................................ 29

6.3

CONNECTION

TERMINALS

CAMERA

CONTROL

UNIT

(CCU) .................................... 30

6.4

PERFORMANCES

/FUNCTIONS .......................................................................................... 30

6.5

ADJUSTMENTS

EXTERNAL

CONTROL ........................................................................... 34

6.6

OSD

ARAMETERS SETTINGS

................................................................................................... 37

6.7

IN ASSIGNMENT

...................................................................................................................... 42

6.7.1

Pin assignment & interfacing details.................................................................................. 43

6.8

ERIODIC

HECKS

.................................................................................................................... 43

MECHANICAL CHECKS AND ADJUSTMENTS ...................................................................... 44

7.1

ARTS WHICH NEEDS PERIODIC ADJUSTMENTS

........................................................................... 44

7.1.1

BRAKES............................................................................................................................. 44

7.1.2

BEARINGS......................................................................................................................... 45

7.1.3

V-BELT............................................................................................................................... 46

7.1.4

CHAIN ................................................................................................................................ 46

7.2

ARTS WHICH NEEDS SERVICING OR REPLACEMENTS

.................................................................. 47

7.2.1

V-Belt ................................................................................................................................. 47

7.2.2

Bearings ............................................................................................................................. 47

7.2.3

Brake liners ........................................................................................................................ 48

7.3

ROUBLE SHOOTING AND RECTIFICATION

................................................................................... 48

APPENDIX I ............................................................................................................................... 50

8.1

PECIFIC

RROR

ODE

ANDLING

............................................................................................ 50

8.1.1

Unit not turning ON ............................................................................................................ 50

8.1.2

No X-ray ............................................................................................................................. 51

8.1.3

No Standby ........................................................................................................................ 53

8.2

NITIALISATION

RROR CODES

................................................................................................... 54

8.2.1

CodE 90 (EPROM CHECKSUM FAILURE) ..................................................................... 54

8.2.2

CodE 96 (KV SOLL FAILURE) ......................................................................................... 54

8.2.3

CodE 97 ( mA FAILURE) .................................................................................................. 54

8.2.4

CodE 99 (LAST RESET BY WATCH DOG TIMER)......................................................... 54

8.3

TANDBY

RROR CODES

........................................................................................................... 55

8.3.1

CodE 02 : +15 V Supply Error ........................................................................................... 55

8.3.2

CodE 03 & 04 : Iheiz < Istby & Iheiz > Istby ...................................................................... 56

8.3.3

CodE 05 : kVist <> 0 .......................................................................................................... 59

8.3.4

CodE 06 : JR <> 0 ............................................................................................................. 60

8.3.5

CodE 33 : Main Inverter Short Circuit ................................................................................ 61

8.4

EXPOSURE

ERROR

CODES................................................................................................ 62

8.4.1

CodE 11 : Main Inverter Short Circuit ................................................................................ 62

8.4.2

CodE 12 : kVist > kVmax ................................................................................................... 63

8.4.3

CodE 13 : Iheiz > Imax OR JR > Jrmax............................................................................ 64

8.4.4

CodE 14 : kVist < kVsoll .................................................................................................... 65

8.4.5

CodE 15 : JR < JRS........................................................................................................... 66

8.4.6

CodE 17 : Exposure terminated by Backup Timer ............................................................ 67

8.4.7

CodE 18 : Premature termination of Exposure.................................................................. 68

Summary of Contents for MULTIMOBIL 5C
























































Search results

Summary of Contents for MULTIMOBIL 5C

Reviews:

Siemens MULTIMOBIL 5C, Troubleshooting Manual, Page: 4 / 74

Search results

Summary of Contents for MULTIMOBIL 5C

Reviews: