Siemens MULTIMOBIL 5C Troubleshooting Manual Download Page 22

Page: 22 / 74

Service Instructions

Multimobil 5C

Siemens Ltd. Med India

Version 5.0

Page 21 of 73

5.1.2 Checking the fuses

Open the front cover of the control unit.
Loosen the Fuse carrier, which are mounted on the base of the control unit and check
the continuity of fuse link. If fuse link has responded for over current replace the Fuse
Link.

5.1.2.1

Fuses on Transformer Plate

Identification Rating

Purpose

16 A Delayed

Mains Fuse

16 A Delayed

Mains Fuse

6A Delayed, Glass cartridge

Motor Supply

6A Delayed, Glass cartridge

Motor Supply

6A Delayed, Glass cartridge

Motor Supply

6A Delayed, Glass cartridge

Charging

resistor

capacitor bank

6A Delayed, Glass cartridge

SMPS supply SMPS 1 & 2

6A Delayed, Glass cartridge

SMPS supply D982 & D985

Note: All Fuses are rated for 250V

5.1.2.2

Fuses on D506

Identification Rating

Purpose

250 mA Delayed, Glass Cartridge T1 transformer primary

630 mA Delayed, Glass Cartridge 240/264 V AC Supply

630 mA Delayed, Glass Cartridge 24 V for K3, K4, K5 & K6

relays

4 A Delayed, Glass Cartridge

Filament Circuit

Note: All Fuses are rated for 250V

5.1.2.3

Fuses on D508

Identification Rating

Purpose

100 mA Delayed, Glass Cartridge Collimator power supply

Note: All Fuses are rated for 250V

Summary of Contents for MULTIMOBIL 5C
























































Search results

Summary of Contents for MULTIMOBIL 5C

Reviews:

Siemens MULTIMOBIL 5C, Troubleshooting Manual, Page: 22 / 74

Search results

Summary of Contents for MULTIMOBIL 5C

Reviews: