manualshive.com logo in svg

Siemens MULTIMOBIL 5C, Troubleshooting Manual, Page: 21 / 74

Share
Download
Siemens MULTIMOBIL 5C Troubleshooting Manual Download Page 21

 

Service Instructions

Multimobil 5C

 

Siemens Ltd. Med India

 

Version 5.0 

 

 

Page 20 of 73 

 

 

Copyright 

©

 SIEMENS LTD. All rights reserved. For internal use only

 

 

 

 

 

 

5 Troubleshooting 

Troubleshooting In case of errors, which Impair radiography or fluoroscopy, perform 
the following checks. The components can be identified as shown in the picture. 
 
 
 
C4 
 
LN 
C5 
US 
 
DL 
 
D985 
 
L2 
 
 
 
CCU 

 

SMPS1
SMPS2

D61

D506

D508

D982

T1

U3,U4,U5
U6,U7,U8

 

5.1  Checking the line voltage, fuses and LED’s 

5.1.1  Checking the line voltage 

Measure the supply voltage at site using the digital Multimeter. 
Ensure that the supply conditions 

•

  Voltage – Should be between 99-121V for 110 V line connection, or 170-264V for 

230 V line connection. 

•

  Frequency – Should be 50 or 60 Hz  

•

  Mains Resistance – Should be 0.36

Ω

 max. for 99-121V or 1.5

Ω

 max for 170-265V 

 
Switch the Unit ON 
 

If the Unit can not be switched ON  
Check Supply at Socket. Check Continuity of mains cable 
with the Plug pins. Check Over Current Protective devices 
(Fuse Link) U1 & U2.

 

Switch the Unit OFF. 

NOTICE 

C2

C1

Summary of Contents for MULTIMOBIL 5C











































































Reviews:

No comments