Siemens LOGO! CIM Operating Manual Download Page 21

Page: 21 / 91

Security

3.3 Important notes on using the device

LOGO! CIM
Operating Manual, 10/2021, A5E51250518-AA

External power supply

•

Use only an external power supply that complies with IEC/EN 61010-1 or IEC/EN 61010-2-

201.

•

The output voltage of the external power supply must not exceed 30 VDC.

•

The output of the external power supply must be short-circuit proof.

NOTICE
Power supply

The external power supply for the CIM must meet the requirements for Safety Extra-Low

Voltage (SELV).

Note the information in this section and in the installation and operating instructions from

the manufacturer of the power supply.

WARNING

The equipment is designed for operation with Safety Extra-Low Voltage (SELV).
This means that only SELV complying with IEC/EN61010-1 must be connected to the power

supply terminals.
If the equipment is connected to a redundant power supply (two separate power supplies),

both must meet these requirements.

WARNING

EXPLOSION HAZARD

DO NOT CONNECT OR DISCONNECT EQUIPMENT WHEN A FLAMMABLE OR COMBUSTIBLE

ATMOSPHERE IS PRESENT.

WARNING

EXPLOSION HAZARD

SUBSTITUTION OF COMPONENTS MAY IMPAIR SUITABILITY FOR CLASS I, DIVISION 2 OR

ZONE 2.

WARNING

When used in hazardous environments corresponding to Class I, Division 2 or Class I, Zone

2, the device must be installed in a cabinet or a suitable enclosure.

Summary of Contents for LOGO! CIM




























































































Search results

Summary of Contents for LOGO! CIM

Reviews:

Related manuals for LOGO! CIM

Brands by name

Popular brands

Siemens LOGO! CIM, Operating Manual

Search results

Summary of Contents for LOGO! CIM

Reviews:

Related manuals for LOGO! CIM

Brands by name

Popular brands