Siemens FCI2016-U1 Mounting & Installation Download

Page: 32 / 46

Periphery board (500p) FCI2017
Configuration input power and battery

32 | 46
Building Technologies

A6V10315038_f_en_--

Siemens Industry, Inc.

2016-02-25

2.4.3 X302 Power supply 2 terminal block

Terminal block X302 may only be used for an additional PS300 when the system

requirements exceed 300 W. The housing (3HU) is the only housing that is capable of

having two PS300 supplies connected at the same time. No power supply (170 W)

may be connected to terminal block X302.

Terminal X301 must always have a power supply connected. When a single power

supply is used, it must be connected to terminal X301.

Check whether jumper X305 is in position 2-3 before PS300 #1 is connected to X301

or #2 to X302. Make sure line voltage is not present on the system, and that the

breaker in the panel is off. Both power supplies need to be connected before line

voltage is switched on at the panel. X301 and X302 should never be

connected/disconnect with line voltage present. Batteries may only be connected after

the system is brought up on line voltage power.

Designation

Description

BROO

(White) AC low signal. Signals when the supply system

connection drops below AC 102 V.

PSSI

(Green) Power supply status indication. Used by the

periphery board to know the health of the power supply.

GND

(Black) Return (ground)

+24 V

(Red) DC +24 V system supply

Admissible cable cross-section: 1 x 12…18 AWG or 2 x 16…18 AWG

2.4.4 X305 jumper – Power supply 2 on/off

This jumper is used to configure the periphery board for one or two power supplies.

The factory setting may only be changed when a second power supply (300 W) in an

housing (3HU) is supported.

X305

Jumper position

Function

Meaning

1 - 2

Deactivated

PS 2 300 W

Default setting; for power supply (170 W) and a single power

supply (300 W).

2 - 3

Activated

PS 2 300 W

For a second power supply (300 W) in an housing (3HU).
The power supply is activated and is monitored by the system.

2.4.5 X304 Voice 24 V

The X304 connector on the periphery board provides the power for all Voice option

modules inside the VCA2002 Card Cage and for the connected peripherals. The cable

that connects X304 on the Periphery Board to X101 on the Card Cage is included in

the VCA2002's scope of supply.

Summary of Contents for FCI2016-U1















































Search results

Summary of Contents for FCI2016-U1

Reviews:

Related manuals for FCI2016-U1

Brands by name

Popular brands

Siemens FCI2016-U1, Mounting & Installation

Search results

Summary of Contents for FCI2016-U1

Reviews:

Related manuals for FCI2016-U1

Brands by name

Popular brands