background image

3/6 

Siemens 

QAX33.1 – Room unit with PPS2 interface 

CA2N1642en_02 

Building Technologies 

 

30 Jun 2009 

Position Fan 

control 

1)

 Control 

mode 

1)

 

 

Fan controlled automati-
cally by controller  

The controller operates at the “setback” 
setpoints (at night, or when room is un-
occupied or occupied intermittently)  

Auto 

Fan controlled automati-
cally by controller 

Comfort mode (room occupied) 

 

Manual, fan speed 1 

 

 

Manual, fan speed 2 

 

 

Manual, fan speed 3 

 

1) 

For details of these functions, refer to the application description for the relevant controller range.  
 
 

01884

 

 
 
 
 
 
Address plugs inside the housing 
They allow setting the address in cases where several 
room units are connected to one controller. 
The room units are delivered with address 1. 

Disposal 

 

The device is classified as waste electronic equipment in terms of the European Direc-
tive 2002/96/EC (WEEE) and should not be disposed of as unsorted municipal waste. 
The relevant national legal rules are to be adhered to.  
Regarding disposal, use the systems setup for collecting electronic waste. 
Observe all local and applicable laws. 

Engineering notes 

The device receives its power from the connected controller via the PPS2 interface 
(extra low voltage).

 

Only one room unit may be connected to a RX… room controller.  

A maximum of 5 room units may be connected to a PXC… automation station (they are 
identified by different settings of their address plugs) 

A twisted-pair cable is required for the connection to the controller.  
DESIGO RX uses four-core cables, DESIGO PX uses two-core cables (see the respec-
tive installation guides). Screening is not required. 

Mounting 

 

The room unit is suitable for wall-mounting and for mounting on a recessed conduit 
box.  

 

Do not mount in recesses, shelves, behind curtains or doors, or above or near heat 
sources. 

 

Avoid exposure to direct sunlight or draughts.  

 

The electrical wiring conduit must be sealed where it joins the room unit, to prevent 
the occurrence of draughts in the conduit which could affect the sensor. 

 

The specified ambient conditions must be complied with.  

 

Mounting instructions are printed on the room unit packaging.  

 

A mounting kit is included with the unit. 

Address plugs 

Summary of Contents for DESIGO RX QAX33.1







Reviews: