manualshive.com logo in svg

Siemens ASIC SIM 1-2, Function Manual

Share
Download
Siemens ASIC SIM 1-2 Function Manual Download Page 25

Functional Description of the SIM 1-2 

SIM 1-2 
C79000-G8976-C215-01 

25

 

2.4.2  Power Supply VE 

 
 

Caution 

The VE voltage of 6.3 V generated by the shunt regulator cannot be used 
immediately after turning on the power supply of the external application 
electronics since this can disrupt the startup of the SIM 1-2 considerably. 

 

On completion of the startup phase (indicated by RESETXN), the VE voltage can 
be used to supply the external application electronics. It is, however, important to 
make sure that the VE never falls below 80% as a result of sudden load changes.  

If the VE voltage sinks below 90% of VE

SOLL

, a prewarning PDWNXN (low-active) 

is output (PDWNXN changes to logic '0' for 10 µs). Communication over TxE, TxS, 
RxA and RxS is not affected by this.  

If the VE voltage falls below 80% of VE

SOLL

, the DC/DC converter and the VREG 

regulator are turned off. They start again only when VE has reached 92 % again.  

When using C

VE

 backup capacitors higher than 33 µF, it is advisable to connect a 1 

Ω

 resistor in series with the capacitor C

VE

 to minimize the risk of superimposing 

oscillations on the VE power supply. 

Summary of Contents for ASIC SIM 1-2































































Reviews:

No comments

Brands by name

Popular brands

Load more brands