manualshive.com logo in svg

Siemens ASIC SIM 1-2, Function Manual

Share
Download
Siemens ASIC SIM 1-2 Function Manual Download Page 2

 

Siemens AG 

Automation and Drives 

Industrial Communication 

Postfach 4848, D-90327 Nürnberg 

Copyright © Siemens AG,  
C79000-G8976-C215-01 
Subject to technical change. 

Siemens Aktiengesellschaft

 

Printed in the Federal Republic of Germany 

2

 

 

Classification of Safety-Related Notices 

This document contains notices which you should observe to ensure your own 
personal safety, as well as to protect the product and connected equipment. These 
notices are highlighted in the manual by a warning triangle and are marked as follows 
according to the level of danger: 

 

Danger 

indicates that death, severe personal injury 

will

 result if proper precautions are not 

taken. 

 

 

Warning 

indicates that death, severe personal injury 

can

 result if proper precautions are not 

taken. 

 

 

Caution 

with a warning triangle indicates that minor personal injury can result if proper 
precautions are not taken. 

 

 

Caution 

without a warning triangle indicates that damage to property can result if proper 
precautions are not taken. 

 

 

Notice 

indicates that an undesirable result or status can result if the relevant notice is 
ignored. 

 

 

Note 

highlights important information on the product, using the product, or part of the 
documentation that is of particular importance and that will be of benefit to the user. 

 

Trademarks 

SIMATIC

®

, SIMATIC NET

®

, SIMATIC NET Networking for Industry

®

, SINEC

®

, 

SCALANCE

®

 and SINAUT

®

 are registered trademarks of Siemens AG. 

Third parties using for their own purposes any other names in this document which 
refer to trademarks might infringe upon the rights of the trademark owners. 

Disclaimer 

We have checked the contents of this manual for agreement with the hardware and 
software described. Since deviations cannot be precluded entirely, we cannot 
guarantee full agreement. However, the data in this manual are reviewed regularly 
and any necessary corrections included in subsequent editions. Suggestions for 
improvement are welcome. 

Summary of Contents for ASIC SIM 1-2































































Reviews:

No comments

Brands by name

Popular brands

Load more brands