manualshive.com logo in svg

Siemens as-interface ANALYSER 3RK1 904-3AB01, Manual, Page: 5 / 46

Share
Download
Siemens as-interface ANALYSER 3RK1 904-3AB01 Manual Download Page 5

                          

   

         

AS-Interface Analyser 

Safety

s

Subject to reasonable modifications due to technical advances.

Printed in Germany

SIEMENS AG  ·  Low-Voltage Controls ·  Phone +49 911 895 59 00  ·  Fax +49 911 895 59 07  ·   Internet: http://www.siemens.com/lowvoltage/technical-assistance

iss

ue da

te

 23.

8.

2006

5

2

Safety

2.1

Intended Use

2.2

General Safety Information

The protection of operating personnel and the system against possi-
ble danger is not guaranteed if the control interface unit is not oper-
ated in accordance with its intended use.
The device may only be operated by appropriately qualified person-
nel in accordance with this operating manual.

Safety and correct functioning of the device cannot be guaranteed if 
any operation other than that described in this operation manual is 
performed.
Connecting the equipment and any maintenance work to be carried 
out with voltage applied to the equipment must exclusively be per-
formed by appropriately qualified electrotechnical personnel.
In case a failure cannot be repaired, the device must be taken out of 
operation and kept from inadvertently being put back into operation.
Repair work is to be carried out by the manufacturer only. Additions 
or modifications to the equipment are not allowed and will void the 
warranty.

The operator is responsible for the observance of local safety stan-
dards.

Summary of Contents for as-interface ANALYSER 3RK1 904-3AB01















































Reviews:

No comments