Siemens 7XV5550-0xA00 Series Manual Download Page 28 | Manualshive

Page: 28 / 52

background image

Page 28 from 52

Active Mini-Starcoupler

14.01.2002

5.2.4 RS232

connection

•

After the connection of a serial cable to the 9 pole Sub-D connector
at the device (X1) it should be screwed. For temporally use it´s not
necessary to screw it. But please check if it´s connected.

5.2.5 Commissioning

•

Clip the Active Mini-Starcoupler on the top–hat rail according EN
50022 with the help of clip-on mounting. Do not make any changes
at the device.

•

Check whether the operation data comply with the values on the
rating plate. Not change any DIP-switch at the device, before
reading this manual.

•

Connect FO cable to FO receiver (Rx) and FO transmitter (Tx) with
the help of FSMA or ST plugs. Be carefull when connecting the FO
plugs and avoid any dust at the FO – connections.

•

Connect to RS485 and RS232 terminals and screw them for
permanent use.

•

Connect the alarm relay terminals X7.

•

Connect auxiliary power to the terminals X2 (DC: L+ / AC: L1 and
DC: L- / AC: N).

•

The device is ready for use after switching on the auxiliary power.
The green LED `RUN´ lights up.

•

Parametrize the device with a terminal program at a PC via it´s
RS232 interface.

•

The LED's ´MASTER´ and ´SLAVE´ blink or light, if datas are
exchanged between Master- and Slave-interfaces.

5.3 Maintenance

The Active Mini-Starcoupler requires no maintanance. For cleaning
please use a dry and free of fuzz rag. Put the caps onto the FO-
interfaces to avoid dust pollution and interference from sun light or any
artifical light source.

Do not use any liquid agents or substances for cleaning.

«
...
26
27
28
29
30
...
»

Summary of Contents for 7XV5550-0xA00 Series





















































Reviews:

No comments

Related manuals for 7XV5550-0xA00 Series

DMS-1250 Series

Brand: D-Link Pages: 38

DL-DVI-MUX2-NT SERIES

Brand: G&D Pages: 76

Brand: Key Digital Pages: 20

Brand: Network Technologies Pages: 7

Brand: Origin Instruments Pages: 6

Brand: KDS Pages: 10

LMP-2012G-SFP Series

Brand: ANTAIRA Pages: 2

Brand: Edge-Core Pages: 2

Brand: CityGrow Systems Pages: 21

Brand: Gefen Pages: 136

Brand: Quark-Elec Pages: 10

Brand: Tripp Lite Pages: 12

Brand: Kramer Pages: 32

ACTIVE with NETATMO

Brand: Velux Pages: 20

Draco tera K480-80C

Brand: Ihse Pages: 214

Brand: Digi Pages: 21

Brand: ExaSAN Pages: 44

Brand: Wise Pages: 11

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands