Siemens 7ME652 Operating Instructions Manual Download Page 49

Page: 49 / 86

Technical data

8.1

MAG 5100 W

Table 8-1

Technical data

Version

MAG 5100W (7ME6520)

MAG 5100W (7ME6580)

Product characteristic

Mainly for the European market
EPDM or NBR lining

Mainly for the non-European market
Ebonite lining

Design and nominal size

Coned sensor:

● DN 15 to 300 (½" to 12")

Full bore sensor:

● DN 350 to 1200 (14" to 48")

Full bore sensor:

● DN 25 to 2000 (1" to 78")

Measuring principle

Electromagnetic induction

Excitation frequency
(Mains supply: 50 Hz/60 Hz)

DN 15 to 65 (½" to 2½"):

● 12.5 Hz / 15 Hz

DN 80 to 150 (3" to 6"):

● 6.25 Hz / 7.5 Hz

DN 200 to 300 (8" to 12"):

● 3.125 Hz / 3.75 Hz

DN 350 to 1200 (14" to 48"):

● 1.5625 Hz / 1.875 Hz

DN 25 to 65 (1" to 2½"):

● 12.5 Hz / 15 Hz

DN 80 to 150 (3" to 6"):

● 6.25 Hz / 7.5 Hz

DN 200 to 1200 (8" to 48"):

● 3.125 Hz / 3.75 Hz

DN 1400 to 2000 (54" to 78"):

● 1.5625 Hz / 1.875 Hz

SITRANS FM MAG 5100 W

Operating Instructions, 01/2020, A5E03063678-AC

Summary of Contents for 7ME652























































































Search results

Summary of Contents for 7ME652

Reviews:

Siemens 7ME652, Operating Instructions Manual, Page: 49 / 86

Search results

Summary of Contents for 7ME652

Reviews: