Siemens 7ME652 Operating Instructions Manual Download Page 33 | Manualshive

Page: 33 / 86

Siemens 7ME652 Operating Instructions Manual Download Page 33

Connecting

5

The following contains a short description of how to connect a remote mounted sensor to a

transmitter type SITRANS FM MAG 5000 / 6000 or MAG 6000 I. For more information, e.g.

about wiring of power supply and outputs, refer to the Operating Instructions for the respective

transmitters.

Before connecting

● Check that serial numbers on sensor and SENSORPROM® unit are identical.

WARNING

The pertinent regulations must be observed for electrical installation.
● Never install the device with the mains voltage switched on!
● Danger of electric shock!
● The electrodes and magnetic current line may only be connected when the device is not

connected to the power supply.

● If the housing is under voltage (power supply), the cover may be unscrewed by qualified

personnel only.

WARNING

Mains supply from building installation Class II
A switch or circuit breaker (max. 15 A) must be installed in close proximity to the equipment

and within easy reach of the operator. It must be marked as the disconnecting device for the

equipment.

SITRANS FM MAG 5100 W

Operating Instructions, 01/2020, A5E03063678-AC

33

«
...
31
32
33
34
35
...
»

Summary of Contents for 7ME652























































































Reviews:

No comments