Siemens 6ES7547-1JF00-0AB0 Manual Download Page 34

Page: 34 / 41

Technical specifications

Communication module IO-Link Master CM 8xIO-Link (6ES7547-1JF00-0AB0)
Manual, 03/2019, A5E45488510-AA

Article number

6ES7547-1JF00-0AB0

•

between the channels and backplane bus

Yes

Isolation

Isolation tested with

707 V DC (type test)

Ambient conditions
Ambient temperature during operation

•

horizontal installation, min.

0 °C

•

horizontal installation, max.

60 °C; Observe derating

•

vertical installation, min.

0 °C

•

vertical installation, max.

40 °C; Observe derating

Dimensions

Width

35 mm

Height

147 mm

Depth

129 mm

Power reduction (derating) to total current of outputs, per module,

The following derating curves show the load capacity of the transducer supply outputs in

relation to the mounting position and the ambient temperature.

①

Horizontal mounting of the system

②

Vertical mounting of the system

Figure 6-1

Derating curve, IO-Link master

Summary of Contents for 6ES7547-1JF00-0AB0










































Search results

Summary of Contents for 6ES7547-1JF00-0AB0

Reviews:

Related manuals for 6ES7547-1JF00-0AB0

Brands by name

Popular brands

Siemens 6ES7547-1JF00-0AB0, Manual

Search results

Summary of Contents for 6ES7547-1JF00-0AB0

Reviews:

Related manuals for 6ES7547-1JF00-0AB0

Brands by name

Popular brands