manualshive.com logo in svg

Siemens 3200 Series, Service Instructions Manual, Page: 87 / 106

Share
Download
Siemens 3200 Series Service Instructions Manual Download Page 87

Mechanical systems

10 - 11

Siemens-Elema AB

 

SPR8-215.898.02

Page 11 of 28

MOBILETT Plus/ Plus E

Solna, Sweden

Rev. 01

01.02

SPS-UD

 

 

MOBILETT Plus only

Adjustment and replacement of the turn plate

10

•

The turn plate mechanism must be removed for adjustment or replacement.

•

Ensure compliance with the safety information in the section:
"Safety information and protective measures".

MOBILETT Plus only

•

Remove the supporting wheels.

•

Jack up and block the unit securely 5 cm above the floor. This must be done properly so 
that the unit does not tip over.

•

Disconnect all cables, ground connection and K68, according to (Fig. 13).

Never work with the system open if the capacitor is charging or 
has just been charged.

The capacitor bank may still be charged even if the system is 
switched OFF and the mains cable is disconnected. 
Life-threatening electric shock hazard exists.

See Chap.:
"Protective measures when working on the capacitor bank".

Equipment required:

2 pieces of wood (50 x 70 x 500 mm)

Fig. 13

DANGER

Shaft

K68

Locking

Locking ring

ring

Summary of Contents for 3200 Series











































































































Reviews:

No comments